Thanks for choosing our DUO
G2
LED Floodlight products.
We strongly recommend that you read this manual carefully before installation.
HANECO LED DIMMER INSTALLATION GUIDE
DUO
G2
Last updated 12/02/24
For more information
www.haneco.com.au
1300 001 LED
After wiring and installation onto
grid plate, remove the rotary knob.
1
2
Turn the dimmer shaft
anti-clockwise until the required
minimum brightness is reached
(or clockwise to set max
brightness level).
3
Align the mechanical stop of the
rotary knob toward the LEFT side
of the mechanical stop on the
dimmer housing to prevent further
anti-clockwise adjustment
(or RIGHT side when setting
max brightness level).
4
Contents
PRODUCT CODE: DUO350WG2
MAX DIMMER LOAD
AND MULTI GANG
UNSWITCHED ACTIVE
NEUTRAL
LOAD
SWITCHED/
DIMMED ACTIVE
DIMMER
ONE WAY DIMMING
(ON/OFF ENABLED)
NEUTRAL
ACTIVE
LOAD
SWITCH
SWITCH
LOOP
LOOP
C
2
2
C
1
1
DIMMER
TWO WAY DIMMING
(ON/OFF DISABLED)
**Multi Gang
Derating
350
W
I 1
**
300
W
I 2
**
250
W
I 3
**
200
W
I 4
**
Connection Diagram
Operating Temp
0Cº - 50Cº
Thermal Derating
25Cº - 50Cº
(350W - 175W)
Technical Specifications
WARNING
* The integrated push switch allows ON/OFF switching of LOAD by a momentary press of rotary knob.
Two way switching is not possible with the integrated push switch.
ON/OFF
1 CLICK
DIM DOWN OVER 30 MINS
3 CLICKS
DIM UP OVER 30 MINS
4 CLICKS
ENTER SETUP MODE
LONG PRESS 2 SECS
ENABLE/DISABLE BACKLIGHT
2 CLICKS
ENABLE/DISABLE PUSH SWITCH*
3 CLICKS
SET MINIMUM BRIGHTNESS / CANCEL
4 CLICKS
SET MAXIMUM BRIGHTNESS / CANCEL
5 CLICKS
MAXIMUM COMPATIBILITY
6 CLICKS
OPTIMISED DIMMING
7 CLICKS
RESET TO FACTORY SETTINGS
9 CLICKS
Setup
• This product must be installed by a licensed electrician in accordance with all the requirements of AS/NZS 3000 (current edition) and
other relevant Standards and Regulations
• ENSURE electricity is disconnected prior to installation
• Indoor Use only. Not suitable for damp or explosive environments
• Complies to Australian Standards AS 60669.2.1 and AS CISPR 15 (x2 Capacitor IEC 60384-14)
• No User serviceable parts inside
• Dimming circuits and product compatibility must be validated by the installer before installation.
Haneco cannot be responsible for third party changes in dimmer compatibility
• A load correction device – x2 Capacitor type 275Vac, 0.10µF, 40/110/56/B – has been included with your DUO
G2
Dimmer. If flickering of the luminaire
load is experienced, connect the load correction device in parallel with the connected load of the DUO
G2
dimmer to improve performance.
ENTER SETUP MODE
LONG PRESS 2 SECS
ENABLE/DISABLE BACKLIGHT
2 CLICKS
ENABLE/DISABLE SWITCH
3 CLICKS
SET MINIMUM BRIGHTNESS
4 CLICKS
SET MAXIMUM BRIGHTNESS
5 CLICKS
MAXIMUM COMPATIBILITY
6 CLICKS
OPTIMISED DIMMING
7 CLICKS
RESET TO FACTORY SETTINGS
9 CLICKS
ON/OFF
1 CLICK
DIM DOWN OVER 30 MINS
3 CLICKS
DIM UP OVER 30 MINS
4 CLICKS
2. Attach cover
1. Apply label to grid
This label should be placed on the
main switchboard in a visible area.
CAUTION
This installation contains
solid state devices.
A low reading may be obtained
if megger testing.
Solid state devices are installed
in the following circuits.
*Sticker denotes dimmer location
L1 L2 L3 L4
L1
L2 L3 L4
