background image

3

5 INCH CHIPPER/SHREDDER/BLOWER

ENGLISH

      

SAFETY

1.5  MAINTENANCE AND STORAGE SAFETY

1.6  TOWING SAFETY

1.7  BATTERY SAFETY

DANGER / POISON

          SHIELD EYES

EXPLOSIVE GASES 

CAN CAUSE

BLINDNESS OR

INJURY

      NO

•  SPARKS

•  FLAMES

•  SMOKING

SULFURIC 

ACID

CAN CAUSE

BLINDNESS OR

SEVERE BURNS

FLUSH EYES

IMMEDIATELY

WITH WATER

GET 

MEDICAL

HELP

FAST

KEEP OUT OF THE REACH OF CHILDREN. DO NOT TIP.  KEEP VENT CAPS TIGHT AND LEVEL.

14. 

Check blade bolts for proper torque after every 8 hours 

of  operation.  Check  blades  and  rotate  or  resharpen 

daily or as required to keep blades sharp.  Failure to do 

so may cause poor performance, damage or personal 

injury and will void the machine warranty.

1. 

Rotate the discharge tube to face the opposite direction 

of the towing vehicle before towing.

2. 

Insert transport safety pin and clip, and set brake handle 

to locked position, if applicable.

3. 

Connect hitch safety chains.  Tighten trailer hitch bolts.  

Do not attempt to tow the trailer if the vehicle is not 

equipped with a 2” (50 mm) ball.

4. 

Do not exceed the maximum towing speed indicated 

on  tire  sidewall.    Inflate  tires  to  manufacturer’s 

specifications as stated on the tire sidewall.

5. 

Optimum  towing  performance  can  be  achieved  by 

maintaining a horizontal trailer hitch.

6. 

Check wheel lug bolts periodically to ensure they are 

tight and secure.

7. 

Make sure the jack stand and the rear stabilizer (where 

applicable) on the trailer are in the UP position during 

towing.  Place  the  jack  stand  on  a  level  surface  and 

secure it in the DOWN position before using.

8.  Never allow passengers to ride on the machine.
9. 

If applicable, shut off fuel supply when towing.

10. 

Towing  laws  may  vary  in  different  countries/regions/

states. It is recommended that you contact your local 

motor vehicle department for any special regulations 

that pertain to towing and know the laws of any country/

region/state you travel through.

Improper use and care of the battery on electric start models 

can result in serious personal injury or property damage.  

Always observe the following safety precautions.

Poison/Danger  -  Causes  Severe  Burns.  The  battery 

contains  sulfuric  acid.   Avoid  contact  with  skin,  eyes  or 

clothing.  Keep out of reach of children.

• 

ANTIDOTE-External Contact:

  Flush immediately 

with water.

• 

ANTIDOTE-Internal: 

 Drink a large amount of water 

or milk.  Follow with milk of magnesia, beaten egg 

or vegetable oil. Call a physician immediately. 

• 

ANTIDOTE-Eye Contact:  

Flush with water for 15 

minutes. Get prompt medical attention.

1. 

The battery produces explosive gases.  Keep sparks, 

flame or cigarettes away.  Ventilate area when charging 

battery.   Always  wear  safety  goggles  when  working 

near battery.

2. 

The battery contains toxic materials.  Do not damage 

battery  case.    If  case  is  broken  or  damaged,  avoid 

contact with battery contents.

3. 

Neutralize  acid  spills  with  a  baking  soda  and  water 

solution.  Properly dispose of a damaged or worn-out 

battery.  Check with local authorities for proper disposal 

methods.

4. 

Do not short circuit battery. Severe fumes and fire can 

result.

5. 

Before  working  with  electrical  wires  or  components, 

disconnect  battery  ground  (negative)  cable  first.  

Disconnect positive cable second.  Reverse this order 

when reconnecting battery cables.

1. 

Before  inspecting,  servicing,  storing,  or  changing 

an  accessory,  shut  off  the  machine  and  make  sure 

all moving parts have come to a complete stop. 

Disconnect  the  battery  and  remove  the  ignition  key 

where applicable.

2. 

Replace  any  missing  or  unreadable  safety  decals.  

Refer to the safety decal section for part numbers.

3. 

Allow machine to cool before storing in an enclosure.

4. 

Store the machine out of reach of children and where 

fuel vapors will not reach an open flame or spark.

5. 

Never store this machine with fuel in the fuel tank inside 

a  building  where  fumes  may  be  ignited  by  an  open 

flame or spark.  Ignition sources can be hot water and 

space heaters, furnaces, clothes dryers, stoves, electric 

motors, etc.

6. 

Drain the fuel and dispose of it in a safe manner for 

storage periods of three months or more.

Summary of Contents for BEAR CAT SC5720B































Reviews: