Echo 77412 Owner'S Manual Download Page 7

Page: 7 / 43

4.5 INCH CHIPPER

SAFETY

Shut off machine immediately if the machine becomes

12.

clogged, the cutting mechanism strikes any foreign

object, or the machine starts vibrating or making an

unusual noise. Shut off power source, disconnect

spark plug wire from spark plug and make sure all

moving parts have come to a complete stop. After

machine stops:

Inspect for damage.

Replace or repair any damaged

parts.

Check for and tighten any loose

parts.
Check blade bolts for proper torque after every 8 hours

13.

of operation. Check blades and rotate or resharpen

daily or as required to keep blades sharp. Failure to do

so may cause poor performance, damage or personal

injury and will void the machine warranty.

1.4 oPeraTion SafeTY (conT.)

1.5 PTo SafeTY

Read and follow instructions on pTO safety decals.

Stay alert and pay attention when pTO is operating.

keep bystanders, especially children, away from pTO

driveline.
Check the driveline to ensure it is attached securely

to the power supply.
keep guards and shields in place at all times while

operating. Disengage pTO, shut off power source,

remove key and make sure all moving parts have

come to a complete stop before removing guards or

shields.
Clothing worn by op-

erator must be fairly

tight. Never wear loose

fitted jackets, shirts, or

pants when working

around the pTO. Tie

long hair back or put

under a cap.
keep hydraulic hoses,

electric cords, chains and other items from contacting

the driveline.
Do not exceed the recommended 540 Rpm pTO

operating speed.

Before inspecting or ser-

vicing the pTO drive area,

disengage the driveline,

shut off power source,

remove key and make

sure all moving parts

have come to a complete

stop.
keep hands, feet, and

10.

clothing away from all

pTO drive parts.

Do not clean, lubricate or adjust the PTO shaft when

11.

it is running.

1.6 baTTerY SafeTY

Improper use and care of the battery on electric start mod-

els can result in serious personal injury or property dam

age. Always observe the following safety precautions.

poison/Danger - Causes Severe Burns. The battery

contains sulfuric acid. Avoid contact with skin, eyes

or clothing. keep out of reach of children.

ANTIDOTE-External Contact: Flush immediately

with lots of water.
ANTIDOTE-Internal: Drink large quantities of water

or milk. Follow with milk of magnesia, beaten egg

or vegetable oil. Call a physician immediately.
ANTIDOTE-Eye Contact: Flush with water for 15

minutes. Get prompt medical attention.

The battery produces explosive gases. keep sparks,

flame or cigarettes away. ventilate area when charg-

ing battery. Always wear safety goggles when working

near battery.
The battery contains toxic materials. Do not damage

battery case. If case is broken or damaged, avoid

contact with battery contents.
Neutralize acid spills with a baking soda and water

solution.
properly dispose of a damaged or worn-out battery.

Check with local authorities for proper disposal meth-

ods.
Do not short circuit battery. Severe fumes and fire

can result.
Before working with electrical wires or components,

disconnect battery ground (negative) cable first. Dis-

connect positive cable second. Reverse this order

when reconnecting battery cables.

danger / PoiSon

SHIELD EyES

ExpLOSIvE GASES

CAN CAuSE

BLINDNESS OR

INjuRy

• SPARKS

• FLAMES

• SMOKING

SuLFuRIC

ACID

CAN CAuSE

BLINDNESS OR

SEvERE BuRNS

FLuSH EyES

ImmEDIATELy

WITH WATER

GET

mEDICAL

HELp

FAST

kEEp OuT OF THE REACH OF CHILDREN. DO NOT TIp. kEEp vENT CApS TIGHT AND LEvEL.

Summary of Contents for 77412












































Search results

Summary of Contents for 77412

Reviews:

Related manuals for 77412

Brands by name

Popular brands

Echo 77412, Owner'S Manual

Search results

Summary of Contents for 77412

Reviews:

Related manuals for 77412

Brands by name

Popular brands