background image

3

The ECHO-TOUCH communicates with a window-mounted base unit which 

is plugged directly into the host security system module.  The window-mount 

antenna should be mounted directly to the interior glass by utilizing the attached 

adhesive pad (clean the glass before adhering) for the best performance.  The 

receiver/transmitter also contains alternative Status Lights and a Valet Switch.  

these may be used, or the original items may be retained.

NOTE: It is recommended to fully charge the controller before use.

Step 1

    

Locate & 

Remove the 

security system’s 

Echo port jumper

connector (it has a 

Red wire loop). 

Step 3 

Program the Echo controller and the 

original 1-way transmitters into the security system 

(see the system’s guide for instructions).

Echo Base 

Transmitter/

Receiver Unit

Step 2 

Plug in and route the Echo 

transmitter/receiver unit wiring harness.  

Using the adhesive tape, mount the Echo 

transmitter/receiver onto an interior glass 

(carefully clean the surface).

Host Omega Security

System Control 

Module

( ( (

ECHO

LED and 

Valet Switch 

plugs.

V

(configurations vary)

Installing & Programming The ECHO System

Summary of Contents for 160





















Reviews: