background image

The ECHO Tec. Membrane Element is guaranteed to be cleanable for a minimum of one year from date 
of shipment, or commissioning of the system by Echo Marine Ltd, provided that cleaning instructions are 
adhered  to  and  foulant  is  acid  soluble  metal  hydroxides  and  calcium  carbonates  or  alkaline  soluble 
organic,  inorganic  substances  and  microbiological  slimes.    The  ECHO  Tec.  Membrane  Element  is  not 
guaranteed against iron fouling (rust), chemical attack, extreme temperatures (over 113º F/under 33ºF), 
drying out, or extreme pressures (over 1000 psig). 
 
 
CAUTION:  Use of parts not supplied directly by Echo Marine (generic parts), including but not limited 
to  maintenance  parts,  pre-filter  elements,  cleaning  and  storage  chemicals,  pump  oil,  spare  parts, 
replacement parts, system components and or system accessories, shall void all warranties expressed or 
implied. 
 
 
 
 

ECHO MARINE LTD. 

1

st

 Avenue South, 

Chaguaramas 
Trinidad W.I. 

 
 

TELEPHONE: 1-868-634-2027 

FAX: 1-868-634-2026 

E-MAIL: [email protected] 

 
 

www.watermakers.net  

 

 

Summary of Contents for Watermakers 500-PRO-1


















Reviews: