920-0102-00 Rev. G
Page 4 of 14
Manufacturer Limited Warranty and Limitation of Liability:
Manufacturer warrants that on the date of purchase this product will conform to Manufacturer’s specifications for this product (which are available from the Manufac
-
turer upon request), and Manufacturer further warrants that this product is free from defects in materials and workmanship. This Limited Warranty extends for sixty
(60) months from the date of purchase. Other warranties may apply, call Manufacturer for details. Manufacturer will, at its discretion, repair or replace any product
found by the Manufacturer to be defective and subject to this Limited Warranty.
DAMAGE TO PARTS OR PRODUCTS RESULTING FROM TAMPERING, ACCIDENT, ABUSE, MISUSE, NEGLIGENCE, UNAPPROVED MODIFICATIONS, FIRE
OR OTHER HAZARD; IMPROPER INSTALLATION OR OPERATION; OR NOT BEING MAINTAINED IN ACCORDANCE WITH THE MAINTENANCE PROCE
-
DURES SET FORTH IN MANUFACTURER’S INSTALLATION AND OPERATING INSTRUCTIONS VOIDS THIS LIMITED WARRANTY.
ORAL STATEMENTS OR REPRESENTATIONS ABOUT THE PRODUCT WHICH MAY HAVE BEEN MADE BY SALESPEOPLE, DEALERS, AGENTS OR OTHER
MANUFACTURER’S REPRESENTATIVES DO NOT CONSTITUTE WARRANTIES. THIS LIMITED WARRANTY MAY NOT BE AMENDED, MODIFIED, OR
ENLARGED EXCEPT BY A WRITTEN AGREEMENT SIGNED BY AN AUTHORIZED OFFICIAL OF MANUFACTURER WHICH EXPRESSLY REFERS TO THIS
LIMITED WARRANTY.
Exclusion of Other Warranties:
MANUFACTURER MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE IMPLIED WARRANTIES FOR MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE ARE HEREBY EXCLUDED AND SHALL NOT APPLY TO THE PRODUCT. BUYER’S SOLE AND EXCLUSIVE REMEDY IN CONTRACT,
TORT, OR UNDER ANY OTHER THEORY AGAINST MANUFACTURER REGARDING THE PRODUCT AND ITS USE SHALL BE THE REPLACEMENT OR REPAIR
OF THE PRODUCT AS DESCRIBED ABOVE.
Limitation of Liability:
IN THE EVENT OF LIABILITY FOR DAMAGES ARISING OUT OF THIS LIMITED WARRANTY OR ANY OTHER CLAIM RELATED TO THE MANUFACTURER’S
PRODUCTS, MANUFACTURER’S LIABILITY FOR DAMAGES SHALL BE LIMITED TO THE AMOUNT PAID FOR THE PRODUCT AT THE TIME OF THE ORIGI
-
NAL PURCHASE. IN NO EVENT SHALL MANUFACTURER BE LIABLE FOR LOST PROFITS, THE COST OF SUBSTITUTE EQUIPMENT OR LABOR, PROP
-
ERTY DAMAGE, OR OTHER SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES BASED UPON ANY CLAIM FOR BREACH OF CONTRACT, IMPROPER
INSTALLATION, NEGLIGENCE, OR OTHER CLAIM, EVEN IF MANUFACTURER OR A MANUFACTURER’S REPRESENTATIVE HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. MANUFACTURER SHALL HAVE NO FURTHER OBLIGATION OR LIABILITY WITH RESPECT TO THE PRODUCT OR ITS
SALE, OPERATION AND USE, AND MANUFACTURER NEITHER ASSUMES NOR AUTHORIZES THE ASSUMPTION OF ANY OTHER OBLIGATION OR LIABIL
-
ITY IN CONNECTION WITH SUCH PRODUCT.
This Limited Warranty defines specific legal rights. You may have other legal rights which vary from state to state. Some states do not allow the exclusion or limitation
of incidental or consequential damages.
© 2008 Electronic Controls Company
Title 13. Motor Vehicles
Division 2. Department of the Califonia Highway Patrol
Chapter 2. Lighting Equipment
Article 7. Mounting Requirements
§685. Installation and Maintenance.
Lighting equipment shall be securely mounted on a rigid part of the vehicle to prevent noticeable vibration of the beam and shall be maintained with the proper aim when the
vehicle is stationary and in motion. No lighting device, unless otherwise permitted, shall be mounted so any portion of the vehicle, load, or vehicle equipment interferes with the
distribution of light or decreases its intensity within the photometric test angles unless an additional device is installed so the combination of the two meets these requirements.
Mounting heights shall be measured from the center of the lamp or reflector to the level surface upon which the vehicle stands when it is without load.
Note:
Authority cited: Section 26103, Vehicle Code. Reference: Sections 24012 and 26103, Vehicle Code.
§686. Mounting of Aftermarket Devices.
Aftermarket lamps, with orientation markings such as “top” shall be mounted in accordance with the markings. Sealed and semisealed optical units shall be installed with the let
-
tering on the lens face right side up. Front and rear reflex reflectors shall be securely mounted on a rigid part of the vehicle with the plane of the lens perpendicular to the roadway
and parallel to the rear axle. Side reflex reflectors shall be mounted with the lens face perpendicular to the roadway and parallel to the rear wheels. Aftermarket devices with
nonadjustable housings shall be mounted with the base on a horizontal or vertical surface, whichever is appropriate, unless different mounting instructions are included with such
devices when offered for sale.
Note:
Authority cited: Section 26103, Vehicle Code. Reference: Sections 24012 and 26103, Vehicle Code.
§687. Mounting of Original Equipment Devices.
Original equipment lamps and reflex reflectors designed for a particular make of vehicle and installed on another vehicle shall be mounted at the same angle as on the vehicle for
which they were designed. They need not be mounted at the same height or lateral spacing as on the original vehicle but must comply with the appropriate height and location
limitations in this title and the Vehicle Code.
Note:
Authority cited: Section 26103, Vehicle Code. Reference: Sections 24012 and 26103, Vehicle Code.
§700. Warning Lamps.
Required front warning lamps other than school bus warning lamps, shall be mounted so the entire projected area of the lens is visible from all eye heights of drivers of other
vehicles at angles within 45 deg left to 45 deg right of the front of the vehicle. If the light within these required angles is blocked by the vehicle or any substantial object on it, an
additional warning lamp shall be displayed within the obstructed angle. Warning lamps may be mounted at any height.
Note:
Authority cited: Section 26103, Vehicle Code. Reference: Sections 24012 and 26103, Vehicle Code.
833 West Diamond St
Boise, Idaho 83705
Customer Service
USA 800-635-5900
UK +44 (0)113 237 5340
AUS +61 (0)3 63322444
www.eccogroup.com
