Page 2 of 4
P/N 920-0323-00 (Rev B) 2018-07-17
© 2018 at Electronic Controls Company
Important!
This unit is a safety device and it must be
connected to its own separate, fused power point to assure its
continued operation should any other electrical accessory fail.
Caution:
When drilling into any vehicle surface, make sure
the area is free from any electrical wires, fuel lines, vehicle
upholstery, etc. that could be damaged
Note:
Operating the Minibar without the lens installed on
this product will result in damage that will not be covered
under warranty.
WARNING!
Maximum recommended vehicle speed for safe
operation using the Vacuum Mount model is 65 mph
(104 km/h), when fitted to the centre of a vehicle roof
of steel construction. Higher speeds could cause
the mount to fail, resulting in the minibar flying off
of the vehicle, which could cause damage to other
vehicles, and injury or death to the passengers.
!
WARNING!
Failure to follow these instructions can result in fire or injury from excessive heat build up.
Operator is responsible for ensuring auxiliary plug fits correctly into auxiliary power plug outlet used.
For proper operation, verify auxiliary power outlet circuit is rated to supply a minimum of 10 amps. (See specifications section
for rated current in amperes).
Do not exceed the current rating for the auxiliary power outlet recommended by vehicle manufacturer.
Keep auxiliary plug and outlet clean and free of debris.
Do not use the auxiliary plug when wet.
Insert auxiliary plug fully into the outlet for proper connection.
Grasp auxiliary plug, NOT cord, to remove from outlet.
Remove auxiliary plug completely from outlet when light is not in use.
!
PULL/ROLL TAB
UPWARD TO
RELEASE VACUUM
PULL/ROLL TAB UPWARD TO RELEASE VACUUM
Figure 1
Installation & Mounting:
Carefully remove the Minibar and place it on a flat surface. Examine
the unit for transit damage, and locate all parts. If damage is found,
or parts are missing, contact the transit company or Vision Alert. Do
not use damaged or broken parts.
Permanent Mounting:
Single Bolt
1. Select the desired location on a flat surface for the minibar
to be mounted.
2. Drill Ø13mm hole for bolt in central location.
3. Remove nut/ shakeproof washer/ washer from bolt.
(rubber spacer to stay on bolt above mounting surface)
4. Place lightbar on roof with wires and bolt through the hole.
5. Ensure bolt head is located correctly in base moulding.
6. Re-apply washer/ shakeproof washer/ nut on underside of
mounting surface and tighten nut to 5Nm.
7. Connect the wires as shown in the wiring section
(see Figure 2).
Double Bolt
1. Select the desired location on a flat surface for the minibar
to be mounted.
2. Drill 2x Ø13mm holes for bolts (Holes have 241.5mm centres).
3. Remove nuts/ shakeproof washers/ washers from bolts.
(rubber spacer to stay on bolt above mounting surface)
4. Place lightbar on roof with wires and bolts through the
holes.
5. Ensure bolt heads are located correctly in base moulding.
6. Re-apply washers/ shakeproof washers/ nuts on
underside of mounting surface and tighten nuts to 5Nm.
7. Connect the wires as shown in the wiring section (see
Figure 2).
The Vacuum-Magnet Mount feature includes suction cups on
the bottom of the minibar, with a magnet inside of the suction
cup, for a secure, temporary mount. The minibar should be
placed in the center of the roof where the least amount of
curvature occurs. Before installing, make sure the mounting
surface is clean and there is no debris on the bottom of the
minibar or on the roof of the vehicle, which could reduce the
holding power of the suction cup and magnet. Place and
remove the minibar without sliding to avoid scratching the
paint on the vehicle. After placement, the minibar should
adhere firmly to the surface. If the unit slides or moves easily,
a proper installation has not been obtained. To release the
vacuum, lift the tab to release the airlock (see Figure 1). To
protect the Vacuum-Magnet Mount assembly, return minibar
to the box when not in use.
Do not attempt to attach the
minibar to an ice-covered surface.
Vacuum-Magnet Mount: