Ecco Axios User Manual Download | Manualshive

Page: 8 / 40

background image

8

Gutter Mounting

Insert the cage nut as shown opposite. It will fit snugly

underneath the mounting foot. Do not install it on the

outside face.

Adjust the spacing of the mounting feet before securely

tightening the nuts.

Hand thread the M6 screw through the star washer and

mounting strap into the cage nut. Be careful not to cross

thread the bolt, and leave loose until later steps.

IMPORTANT

Mounting straps are specific to the vehicle model. Please make sure the straps are suitable for the vehicle before installation.

Open the doors of the vehicle and position lightbar. Use

the strap as a template to drill Ø1/8”/3.17mm holes in

the roof gutter. It may be necessary to pull back the

door sealing gasket or trim. Apply silicone or sealant

around the hole, behind the strap. Secure the straps

with the provided #10 stainless steel sheet metal screws

with washers as shown. Screws should be tightened to

around 5-10 in-lb.

Tighten the M6 screw evenly so that the bar is even and

centered. Reinstall any removed trim and/or weather-

stripping and close doors to check secure fit of the

Please call ECCO Customer Service or your local Axios Distributor for more options.

Roof Mounting Kits

Ford, Truck, 1/2T, 2004-09 ........................................ A1010RMK
Ford, Truck, 3/4T-1T, 1999-2009 ............................... A1012RMK
Ford, Crown Vic, 1998-2013 ..................................... A1013RMK
Ford, Truck, 1/2T, Crew Cab, 1997 ........................... A1014RMK
Ford, Truck, 1/2T, 2010-2015 .................................... A1025RMK
Ford, Super Duty Truck, 2010-2015 ......................... A1026RMK

Vehicle

Part #

GM, Truck, 1/2T-1T, 1999-2009 ................................. A1011RMK
GM, Truck, 1/2T-1T, 2010-2014 ................................. A1027RMK
GM, Truck, 1/2T-1T, 2015 .......................................... A1025RMK
Dodge, Charger, 2007-2010 ..................................... A1029RMK
Dodge, Charger, 2011-2015 ..................................... A1031RMK
Dodge, Truck, 1/2T-1T, 2002-2013 ............................ A1011RMK
Headache Rack Mounting Brackets ........................ A1401RMK

Vehicle

Part #

1

2

3

4

5

«
...
6
7
8
9
10
...
»

Summary of Contents for Axios









































Reviews:

No comments

Related manuals for Axios

Brand: Taurus Pages: 28

Brand: Kärcher Pages: 54

Brand: ABB Pages: 85

Brand: B&K Pages: 12

LOUDEN 200 Series

Brand: ACCO Brands Pages: 144

Brand: B&K Pages: 16

Brand: B&G Pages: 2

Brand: DB Industries Pages: 60

Brand: vc999 Pages: 55

Brand: Salsbury Industries Pages: 4

Crouse-hinds series

Brand: Eaton Pages: 32

Brand: SAFAVIEH COUTURE Pages: 2

Brand: Mangar International Pages: 8

Brand: Malvern Instruments Pages: 30

Brand: zarges Pages: 36

Brand: Qlight Pages: 3

Brand: qtran Pages: 2

Brand: Q-Optics Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands