Ecco Axios User Manual Download | Manualshive

Page: 33 / 40

background image

33

ENGLISH

ASSEMBLY &

CONFIGURATION

Center Illumination

Installation

When installing the center illumination module lens, insert the opposite end of this lens

from the DropLock power adapter into the already installed end lens(es), position on the

chassis, then secure the DropLock power adapter within the area that is covered by the

center illumination module lens. The DropLock power adapter must be installed in either

the front or rear power rail only.

2

60”m/1.5m & 72”/1.8m

For correct operation, the DropLock power adapter must

be installed in either the front or rear power rail only.

Power adapter

«
...
31
32
33
34
35
...
»

Summary of Contents for Axios









































Reviews:

No comments

Related manuals for Axios

Brand: ABB Pages: 18

Brand: R-Tech Pages: 3

Giraffe OmniBed

Brand: Ohmeda Pages: 54

Brand: Bacharach Pages: 48

Brand: dbx Pages: 12

Brand: dbx Pages: 13

Brand: dbx Pages: 72

Brand: dbx Pages: 11

Brand: dbx Pages: 16

Brand: EuroLite Pages: 28

Brand: Nellcor Pages: 161

OXIMAX N-600X Series

Brand: Nellcor Pages: 210

Brand: Oase Pages: 120

Brand: OAKWORKS Pages: 24

Brand: Mach Pages: 12

Brand: Gardco Pages: 17

Brand: H&S Pages: 42

Brand: Aeroflex Pages: 211

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands