background image

www.centralheating.co.uk

I

t

 i

s

 

recommended

 

that

 

your

 

heat

i

ng

 

system

 i

s

 

serv

i

ced

 

regu

l

ar

l

y

 

and

 

that

 

the

 

appropr

i

ate

 

Serv

i

ce

 I

nterva

Record

 i

s

 

comp

l

eted.

Serv

i

ce

 

Prov

i

der

Before completing the appropriate Service Record below, please ensure you have carried out the service as described in the manufacturer’s instructions. 

SERV

I

CE

 

RECORD

SERV

I

CE

 

01

Date:

Engineer name:

Company name:

Telephone No:

Gas safe register No:

Record:

At max. rate:

CO           ppm

AND

CO² %

At min. rate: 

(Where Possible

)

CO           ppm

AND

CO² %

Comments:

Signature

SERV

I

CE

 

02

Date:

Engineer name:

Company name:

Telephone No:

Gas safe register No:

Record:

At max. rate:

CO           ppm

AND

CO² %

At min. rate: 

(Where Possible

)

CO           ppm

AND

CO² %

Comments:

Signature

SERV

I

CE

 

03

Date:

Engineer name:

Company name:

Telephone No:

Gas safe register No:

Record:

At max. rate:

CO           ppm

AND

CO² %

At min. rate: 

(Where Possible

)

CO           ppm

AND

CO² %

Comments:

Signature

SERV

I

CE

 

04

Date:

Engineer name:

Company name:

Telephone No:

Gas safe register No:

Record:

At max. rate:

CO           ppm

AND

CO² %

At min. rate: 

(Where Possible

)

CO           ppm

AND

CO² %

Comments:

Signature

SERV

I

CE

 

05

Date:

Engineer name:

Company name:

Telephone No:

Gas safe register No:

Record:

At max. rate:

CO           ppm

AND

CO² %

At min. rate: 

(Where Possible

)

CO           ppm

AND

CO² %

Comments:

Signature

SERV

I

CE

 

06

Date:

Engineer name:

Company name:

Telephone No:

Gas safe register No:

Record:

At max. rate:

CO           ppm

AND

CO² %

At min. rate: 

(Where Possible

)

CO           ppm

AND

CO² %

Comments:

Signature

SERV

I

CE

 

07

Date:

Engineer name:

Company name:

Telephone No:

Gas safe register No:

Record:

At max. rate:

CO           ppm

AND

CO² %

At min. rate: 

(Where Possible

)

CO           ppm

AND

CO² %

Comments:

Signature

SERV

I

CE

 

08

Date:

Engineer name:

Company name:

Telephone No:

Gas safe register No:

Record:

At max. rate:

CO           ppm

AND

CO² %

At min. rate: 

(Where Possible

)

CO           ppm

AND

CO² %

Comments:

Signature

SERV

I

CE

 

09

Date:

Engineer name:

Company name:

Telephone No:

Gas safe register No:

Record:

At max. rate:

CO           ppm

AND

CO² %

At min. rate: 

(Where Possible

)

CO           ppm

AND

CO² %

Comments:

Signature

SERV

I

CE

 

10

Date:

Engineer name:

Company name:

Telephone No:

Gas safe register No:

Record:

At max. rate:

CO           ppm

AND

CO² %

At min. rate: 

(Where Possible

)

CO           ppm

AND

CO² %

Comments:

Signature

*All installations in England and Wales must be

to Local Authority Building Control (LABC

)

either directly or through a

Competent Persons Scheme. A Building Regulations Compliance

will then be issued to the customer.

© 

H

eating and 

H

otwater Industry Council (

HH

IC

)

46

Summary of Contents for 8116450110
















































Reviews: