background image

4

1-INTRODUCTION

First of all, we would like to thank you for choosing E.C.A brand. E.C.A. Proteus Premix condensing boilers 
have  been  designed  to  meet  for  an  efficient,  safe  and  comfortable  central  heating  and  hot  water 
requirement. The Proteus Premix condensing boilers can possibly use natural gas or LPG according to the 
desired fuel preference. There is no standard LPG models. LPG usage is only possible after gas conversion 
in the field. 

HM Model (Combi Boiler)    : 

Both Central Heating (CH) and Domestic Hot Water (DHW). 

HCH Model (Heat Only)     : 

Only for Central Heating (CH). 

HST Model (System Boiler) : 

Both for Central Heating (CH) and Domestic Hot Water (DHW) with external 

storage tank (not included). 

The assembly and usage information of 24/30/35 kW Proteus Premix condensing boilers are available in 
this manual. Detailed information have been provided in the guide regarding the technical specification of 
the boiler, selection of the  boiler location, fitting  its  water, gas, flue  and  electric supply connections, gas 
conversion, maintenance information and solving of possible failures. Please carefully read the manual in 
order to benefit from all the features of your boiler. 

The Benchmark Checklist and Service Record Card are located at the back of the Operating Manual. 

The Benchmark Checklist must be filled by gas safe engineer during installation. 
Operating  Manual  and  Service  Manual  must  be  handed  over  the  user  for  future 
operations. 

Service Record Card must be filled by gas safe engineer and handed over the user 

after each service operation and annual maintanence. 

1.1 

Installer’s Responsibility 

The installer is responsible for the installation and initial start-up

 

of the boiler. Instructions are given below. 

Check Operating and Service manuals and follow instructions before installation.

Carry out installation in compliance with the prevailing legislation and standarts.

Be sure that the system is flushed and inhibitor added.

Only gas safe engineer must operate the boiler.

Explain the user about installation and operation of boiler.

Fill the Comissioning Checklist.

Give all Operating and Service manuals to user.

The warranty certificate must be registered by gas safe engineer within 30 days after installation.

Summary of Contents for 8116450110
















































Reviews: