background image

Chengdu Ebyte Electronic Technology Co., Ltd.

E90-DTU(400SL30P)

User manual

Copyright ©2012–2019, Chengdu Ebyte Electronic Technology Co., Ltd

18

When module A is the receiver, it can receive the data sent from all modules under channel 0x04. The purpose of

monitor is realized.

7.Operating mode

The E90-DTU has three working modes, which are configured by the host computer software. Among them, when

there is no demand for low power consumption and normal communication is required, it is recommended to configure
the radio to the general mode (mode 0); the factory default setting is the general mode (Mode 0).

Categories

Notes

Mode 0

Normal Mode

Serial port open, wireless open, transparent transmission (factory default

mode), support special command air configuration.

Mode 1

Wor sending

mode

WOR sender

Mode 2

WOR

receiving

mode

WOR receiver

Note: if there is no need for low power consumption, there is no need to care about the wor receiving mode (mode
2).

7.1 Normal mode

Mode 0

Type

Software configuration module working in mode 0

Transmitting

The user can input data through the serial port, and the module will start the

wireless transmission.

Receiving

The wireless receiving function of the module is turned on, and the wireless data

will be output through the serial port pin after receiving.

7.2 Wor sending mode

Mode 1

Type

Software configuration module working in mode 1

Transmitting

When defined as a transmitter, a wake-up code will be automatically added for a

certain period of time before transmission.

Receiving

It can receive data normally, and the receiving function is equivalent to mode 0

7.3 WOR receiving mode

Mode 2

Type

Software configuration module working in mode 2

Transmitting

Wireless transmission off

Receiving

Sleep at ordinary times. Periodically wake up to check whether there is data. If

there is data, receive it and enter sleep after processing.

Summary of Contents for E90-DTU




































Reviews: