ebm-papst K3G560-HE07-01 Operating Instructions Manual Download Page 4

Page: 4 / 13

Operating instructions

K3G560-HE07-01

Translation of the original operating instructions

3. TECHNICAL DATA

3.1 Product drawing

All dimensions in mm.

Inlet ring with pressure tap (k-factor: 348)

Mounting position for vibration-absorbing elements, tightening torque max. 40 Nm

Cable diameter min. 5 mm, max. 13 mm, tightening torque 6 ±0.9 Nm

Cable diameter min. 16 mm, max. 20.5 mm, tightening torque 6 ± 0.9 Nm

Tightening torque 3.5 ± 0.5 Nm

Mounting holes for FlowGrid

Installation position: shaft horizontal (motor support plate must stand upright) or rotor on bottom; rotor on top on request

Item no. 56858-5-9970 · ENU · Change 260717 · Approved 2022-06-23 · Page 4 / 13

ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com

Summary of Contents for K3G560-HE07-01














Search results

Summary of Contents for K3G560-HE07-01

Reviews:

Related manuals for K3G560-HE07-01

Brands by name

Popular brands

ebm-papst K3G560-HE07-01, Operating Instructions Manual

Search results

Summary of Contents for K3G560-HE07-01

Reviews:

Related manuals for K3G560-HE07-01

Brands by name

Popular brands