PRODUCT SPECIFICATION
NOTES
CLEANING
LOADING BLADE
1. Confirm the position of
the blade and change the
settings to 1.9mm.
2. Add the blade on the product.
EUROPET BERNINA INTERNATIONAL B.V.
P.O. Box 6 - 5420 AA Gemert-Bakel
The Netherlands
B.T.W. nr. NL 8143.40.015.B01
WEEE-Reg-Nr: DE 18134493
[email protected] - www.ebi.eu
PRODUCT SPECIFICATION
When the battery power is less than 5%, the charging icon starts
to flash to remind you to charge the clipper.
• After starting, if you do not use any key operation within two
minutes, the screen will close to save electricity.
• Please charge for 3 hours before using the new product.
• After full-charged, the product will smart off power, starting
over- charge protection to prevent over-charge.
• When the product is completely without electricity, the product
will start the discharge protection to protect battery life.
PRODUCT SPECIFICATION
BLADE ADJUSTmENT FUNCTION
1. To adjust upward, push the adjustment button
directly to the required position.
2. To adjust downward press the lock key down
and then push the adjustment button to
the required position.
PRODUCT SPECIFICATION
LOADING & UNLOADING COmB
• LOADING COMB
Hold the both side,match the slot
and push on (avoid losing or
dropping).
• UNLOADING COMB
Push the locked part of the comb
on both sides away (do not press
the front or back part, it may hurt
the comb).
LCD FUNCTION DESCRIPTION
RPM CONTROL FUNCTION
Real-time display shows the running speed of the
product. RPM setting method press “-” or “+” to
set RPM. RPM setting range: 5000-7000
INTELLIGENT CONSTANT RPM CONTROL
FUNCTION
The product maintains a constant speed. When
using the product it can automatically compensate
by decline in the speed of cutting resistance.
RUNNING LIGHT
In the starting state, the running light starts to run
clockwise, the higher speed, the faster cicle goes.
BATTERY POWER REAL TIME DISPLAY
Real-time display shows the power of the Li-ion
rechargeable battery.
CLEANING PROMPT FUNCTION
When the blade is full and filthy, the cleanning icon
will start to flash to remind you should unload the
blade to clean and oiling.
OILING PROMPT FUNCTION
When the blade is full and filthy or the prdouct has
accumulated 60 minutes of running, the oiling icon
will to flash to reminding you to oiling the blade.
• When alarm continues after cleaning and oiling, the blade has
been worn, please replace a new blade.
6
7
4
5
1.
2.
upper blade
lower blade
AUTOmATIC CHARGE FUNCTION
1. Do not tear down the clipper randomly. Do not drop the
clipper.
2. Do not clean product by water flush and keep the unit away
from damp situation.
3. Do not use any corrosives such as alcohol, gasoline etc. to
clean the surface.
4. Avoid charging above 40°C or below 0°C.
How to deal with the battery?
Inside is Li-ion battery. Before abandoning please take the
battery out and deal with the battery in an
environmental-friendly way.
3
4
1
2
3
4
1
2
1. Before unloading the blade, make sure you have turn it off
and separate the power cable from the clipper.
2. Wash the hair between the upper blade and the lower blade off
(please do not take apart the spring of the blade, in case it
breaks).
3. Clean the hair from the clipper by using the brush.
4. After cleaning the blade, add some lubricant oil between the
upper blade and the lower blade. Otherwise the cutting edge will
go dull,make weird noises, give out heat and reduces the effect.
5. Replace the blade (when you hear a click you match it right).
g0236161116_651-435267_clipper_NOIR_102_MANUAL_english.indd 2
06-02-17 11:10
