6.5.2
U-
N
ET OUT ASSIG
N
Assign the processed output signal to a U-Net output channel: U-Net 1 to 32
6.5.3
CHA
NN
EL
N
AME
Enter a name for the output channel, up to 16 alphanumeric characters.
6 . 6
L E V E L
Use the LEVEL function to set Input Channel and Output Channel gain and polarity by selecting the A to
D or 1 to 8 buttons.
Level:
Scroll through and select the gain up to +/- 15 dB in 0.1 dB steps.
Polarity:
Select the polarity: + or -.
6 . 7
X - OV E R ( O u t p u t C h a n n e l s 1 t o 8 )
Use the X-OVER function to set crossover filters for providing an acoustic transition between a multi-
amplified loudspeaker’s subsystems. The crossover filters have the following variable parameters:
HPF / LPF
High Pass Filter / Low Pass Filter
Filt:
Set the selected HPF or LPF to be active or inactive.
Freq:
Scroll through and select the crossover filter frequency from 20 Hz to 20 kHz in
1/24th Octave steps.
Type:
Scroll through and select the crossover type and slope:
6 dB Butterworth, Bessel
12 dB Butterworth, Bessel, Linkwitz-Riley
18 dB Butterworth, Bessel
24 dB Butterworth, Bessel, Linkwitz-Riley
30 dB Butterworth, Bessel
36 dB Butterworth, Bessel, Linkwitz-Riley
42 dB Butterworth, Bessel
48 dB Butterworth, Bessel, Linkwitz-Riley
6 . 8
L I M ( O u t p u t C h a n n e l s 1 t o 8 )
Use the LIM function to set the compressor / limiter parameters:
Lim:
Sets the Comp/Lim to In (active) or Out (inactive).
Thrsh:
Scroll through and select the limiter threshold from 20 dBu to -10 dBu in 0.1 dB steps.
Ratio:
Scroll through and select the compression ratio in integer increments:
1:1 to 20:1, or Inf:1.
Atk:
Scroll through and select the limiter attack from 40 µs to 1 ms in 10 µs steps, 1
ms to 40 ms in 1 ms steps. The default setting is 1 ms.
Rel:
Scroll through and select the limiter release from 10 ms to 2 s in 10 ms steps.
Knee:
Select the aggressiveness of the onset of limiting between a hard or soft knee.
6 . 9
E Q
Use the EQ function to set the Input Channel and Output Channel equalization by selecting the A to D or
1 to 8 buttons. Each channel’s EQ section has 10 filters. Each EQ section has the following variable
parameters. The available parameters depend on the selected Type.
Parametric EQ:
Sets the entire EQ section (filters 1 to 10) to In (active) or Out (inactive).
Type:
Scroll through and select the type for each parametric filter: Bell, 6 dB LoShelf,
12 dB LoShelf, 6 dB HiShelf, 12 dB HiShelf, 6 dB HPF, 12 dB HPF, 6 dB LPF,
or 12 dB LPF.
BW:
Scroll through and select the bandwidth for each filter: 0.02 to 10 octaves.
Freq:
Scroll through and select the frequency for each filter: Variable from 20 Hz to
20 kHz in 1/24th octave steps.
Gain:
Scroll through and select the gain for each filter: +/- 15 dB in 0.1 dB steps.
Filt:
Sets the selected filter (1 to 10) to be In (active) or Out (inactive).
Page 13
