background image

4

Installation

InstructIon manual

   MN050011EN   August 2022   www.eaton.com

Step 4. Tilt XN-332-5ETH-UMS forward and place it against  

 

the DIN rail’s bottom edge in an inclined position.

Step 5. Push the XN-332-5ETH-UMS over the DIN rail’s  

 

top edge.

Figure 5 .  Place the XN-332-5ETH-UMS against the 

bottom edge of the DIN rail

Step 6. Push the locking elements on the back of the  

 

XN-332-5ETH-UMS downward in order to secure  

 

the modules. You can use a screwdriver to do this.

Figure 6 .  Locking the XN-332-5ETH-UMS into place on 

the DIN rail

Step 7.  Check to make sure that the XN-332-5ETH-UMS  

 

is solidly mounted.

Dismantling XN-332-5ETH-UMS

To remove the XN-332-5ETH-UMS, follow the steps below:
Step 1.  Slide the locking elements on the back of the 

 

XN-332-5ETH-UMS upward. You can use a  

 

screwdriver to do this.

Figure 7 .  Disengaging the XN-332-5ETH-UMS

Step 2. Tilt the XN-332-5ETH-UMS forward, and then  

 

pull the block from its bottom edge, away from  

 

the DIN rail.

Figure 8 .  Place the XN-332-5ETH-UMS against the 

bottom edge of the DIN rail

5

4

6

RN
DC

LA

X1

FD

LA

X2

FD

LA

X3

FD

LA

X4

FD

LA

X5

FD

1

2

Summary of Contents for XN300

















Reviews: