Eaton Powerware 9125 User Manual Download

Page: 31 / 78

INSTALLATION

EATON

Powerware

9125 Two-in-One UPS (2500/3000 VA) User’s Guide

164201374 Rev D

www.powerware.com

Plug-Receptacle UPS Installation

NOTE

Do not make unauthorized changes to the UPS or accessories; otherwise, damage

may occur to your equipment and void your warranty.

Figure 18 shows a typical installation only. See “UPS Rear Panels” on
page 33 for the rear panel of each model.

To install a plug-receptacle UPS:

If you are installing power management software, connect your
computer to the UPS communication port using the supplied
communication cable.

Power Cord

Output Receptacles

Communication Port

UPS

EBM

Figure 18. Typical Installation (120V UPS Model Shown)

Plug the equipment to be protected into the appropriate UPS output
receptacles (see page 50 for more information on load segments).

NOTE

DO NOT protect laser printers with the UPS because of the exceptionally high power

requirements of the heating elements.

If an emergency power-off (disconnect) switch is required by local
codes, see “Remote Emergency Power-off Installation” on page 31
to install the REPO switch before powering on the UPS.

Summary of Contents for Powerware 9125















































































Search results

Summary of Contents for Powerware 9125

Reviews:

Related manuals for Powerware 9125

Brands by name

Popular brands

Eaton Powerware 9125, User Manual

Search results

Summary of Contents for Powerware 9125

Reviews:

Related manuals for Powerware 9125

Brands by name

Popular brands