Eaton Powerware 9125 User Manual Download

Page: 23 / 78

INSTALLATION

EATON

Powerware

9125 Two-in-One UPS (2500/3000 VA) User’s Guide

164201374 Rev D

www.powerware.com

Rack-Mount Setup

The UPS can be installed in 19-inch racks and needs only 2U of valuable
rack space.

C A U T I O N

The UPS and EBM are heavy (see page 61). A minimum of two people are required to lift the
cabinets into the rack.

NOTE

Mounting rails are required for each UPS and EBM cabinet. If rails are not already

installed in your rack, contact your local distributor to order rail kits.

To install the UPS and optional EBMs in a rack:

Place the UPS on a flat, stable surface with the front of the UPS
facing toward you.

Attach the supplied mounting handles to the mounting brackets and
secure with the supplied screws (see Figure 5).

Align the mounting brackets with the screw holes on the side of the
UPS and secure with the supplied screws (see Figure 5).

If installing optional EBMs, repeat Steps 1 through 3 for each
cabinet.

Mounting
Handle

Mounting
Bracket

Figure 5. Installing the Mounting Handles and Brackets

Summary of Contents for Powerware 9125















































































Search results

Summary of Contents for Powerware 9125

Reviews:

Related manuals for Powerware 9125

Brands by name

Popular brands

Eaton Powerware 9125, User Manual

Search results

Summary of Contents for Powerware 9125

Reviews:

Related manuals for Powerware 9125

Brands by name

Popular brands