Eaton PMINT, Installation And Use Manual

Page: 11 / 24

11
04/10 AWB1230-1621
Effective April 2010
PMINT—PROFIBUS DP translator
module—installation and use
EATON CORPORATION www.moeller.net/en/support
Table 15. Cause-of-Status Code Definitions
Code Definition Code Definition
0 Unknown 40 Diagnostic failure #1
1 Normal operating mode 41 Low battery
2 External condition #1 42 Multiple causes
3 Instantaneous phase
overcurrent
43 Diagnostic warning #2
4 Instantaneous ground
overcurrent
44 Diagnostic warning #3
5 Instantaneous neutral
overcurrent
45 Diagnostic warning #4
6 Instantaneous residual
overcurrent
46 Diagnostic warning #5
7 Phase inverse-time
overcurrent
47 Diagnostic warning #6
8 Ground inverse-time
overcurrent
48 Diagnostic warning #7
9 Neutral inverse-time
overcurrent
49 Diagnostic warning #8
10 Residual inverse-time
overcurrent
50 Diagnostic warning #9
11 Overvoltage 51 Diagnostic warning #10
12 Undervoltage 52 Diagnostic failure #2
13 Auxiliary overvoltage 53 Diagnostic failure #3
14 Auxiliary undervoltage 54 Diagnostic failure #4
15 Underfrequency 55 Diagnostic failure #5
16 Overfrequency 56 Diagnostic failure #6
17 Current unbalance 57 Diagnostic failure #7
18 Voltage unbalance 58 Diagnostic failure #8
19 Apparent power factor 59 Diagnostic failure #9
20 Displacement power factor 60 Diagnostic failure #10
21 Zone interlock phase 61 Long delay phase overcurrent
22 Zone interlock ground 62 Short delay phase overcurrent
23 Watt 63 Fixed instantaneous phase overcurrent #1
24 VA 64 Bad/missing rating plug
25 VAR 65 Reverse power
26 Power demand 66 Fixed instantaneous phase overcurrent #2
27 VA demand 67 Reverse phase
28 Var demand 68 Reverse sequence
29 Current demand 69 Phase current loss
30 Total harmonic distortion 70 Phase voltage loss
31 Operations count 71 Alarm active
32 Contact maintenance 72 Bad frame
33 Control via communications 73 Phase currents near pickup
34 Contact disagreement 74 Lockout
35 Breaker failure 75 Making current release
36 Operation time exceeded 76 Fixed instantaneous phase overcurrent #3
37 Coil supervision 77 Set points error
38 Programmable logic 78 Overtemperature
39 Diagnostic warning #1 79 Accessory bus
Cause-of-Status Code Definitions (continued)
Code Definition Code Definition
80 Long delay neutral overcurrent 122 Failed to sync on voltage
81 External condition #2 123 Anti-backspin
82 Historical data 124 Zero speed
83 External condition #3 125 Time between starts
84 Ground fault (instantaneous or delay) 126 Source 1
85 Earth fault (instantaneous or delay) 127 Source 2
86 External condition #4 128 Start
87 External condition #5 129 Manual
88 External condition #6 130 Synchronizing
89 External condition #7 131 Starts per hour
90 External condition #8 132 Preferred source
91 External condition #9 133 Plant exerciser
92 Multiple external conditions 134 Neutral ground overvoltage
93 Motor bearing temperature 135 Safety interlock
94 Load bearing temperature 136 Real-time clock
95 Auxiliary temperature 137 High floating voltage
96 Winding temperature 138 Trip blocked
97 Local temperature 139 Incomplete sequence
98 External temperature 140 Cause N/A (none)
99 Rolled phase 141 Trip position
100 Per unit voltage 142 Voltage transient
101 Sensitive 143 Tamper
102 De-energize 144 RTD
103 Non sensitive 145 Differential
104 Time delayed sensitive 146 Frequency out of range
105 Breaker pumping 147 Sensor mismatch
106 Sub-network malfunction 148 Check aux. switch
107 Learning 149 Overcurrent
108 Offline 150 Time delayed Watt-VAR
109 Test 151 Overcurrent Watt-VAR
110 Jam 152 Power
111 Underload 153 Maintenance Mode
112 Delay ground overcurrent 154 Breaker mechanism fault
113 Calibration 155 Automatic reclose lockout
114 Emergency 156 Disconnect position
115 Torque limit 157 Shunt fault problem
116 Deceleration Reserved 158 … 2043
117 Voltage sag
118 Voltage swell 2044 Product specific code 2044
119 Programming error 2045 Product specific code 2045
120 Failed to sync on phase 2046 Product specific code 2046
121 Failed to sync on frequency 2047 Product specific code 2047