background image

MN008006EN Manual 

Efective March 2021    

NOVA LBS Load Break Switch 

www.eaton.com/cooperpowerseries 

13 

 

 

 
 

Grounding on a 3-Wire Uni-Grounded System 

Installation on a 3-wire uni-grounded system must include 
the following (refer to Figure 13): 

• Protection of the switch bushings and the supplying 
transformer with lightning arresters. 
• Grounding of the switch head and tank. 
• Grounding of the transformer tank. 
• Grounding of the control cabinet. 
• Grounding of the SCADA equipment. 

 

 

ADVERTISEMENT 

 

Hazardous Voltage. Use locally approved operator safety procedures for 

proper insulation when maintaining this equipment. High voltage step 

and touch potential is characteristic in uni-ground systems. Failure to 

comply can cause death or severe personal injury. 
 

 

CAUTION 

 

Exported Potential. Do not make direct electrical connections to remote 

devices. All SCADA equipment must be mounted locally or connected 

using the fiber-optic or radio communication accessory. Direct 

connections to remote devices can produce exported potential causing 

equipment damage or personal injury  
 

 

CAUTION 

 

Hazardous Voltage. Do not use a shared low-voltage network to power 

the switch control unless the network is specifically designed to 

withstand maximum ground potential rise. Ground faults on a 

highvoltage network can create a rise in ground potential 
 

 

IMPORTANT 

 

In pole-mounted applications, a ground connection must be made 

between the switch, transformer, LBC control, and SCADA equipment 

for proper protection of the equipment. An improper ground 

connection can cause equipment damage and malfunction. The pole 

ground must be sized per local utility practices to minimize the 

impedance between the switch and the control. 
 

 

IMPORTANT 

 

All external inputs to the control must be routed within 8 inches of their 

corresponding ground. During a surge, a potential of approximately 1.5 

kV per foot can develop in the conductors. Differences between 

conductor and ground path lengths can add additional stress to the 

control components in the event of a power surge. 
 

 

 

Figure 13.

 Recommended grounding method for LBS switches with LBC control and 3-wire system with single ground.

Summary of Contents for NOVA LBS 15


























Reviews: