background image

16

INM MTL SUM5 Rev 1

5.3.1  Mode indicator (M)

The mode indicator uses different colours together with steady, blinking or flashing lights 
to display both the current mode of the isolator and its function. Use the following tables 
to interpret what is displayed. Use the following table to identify the basic mode. 

Channel operation

Channel operation

Red

 – flashing

Not defined

 

Config in base:  No 
Config in UI:      No

Red

 – single blink  

(On 3s, Off 100ms)

Not defined

 

Config in base:  No 
Config in UI:      Yes

Green 

 -  steady

AO

Blue 

 -  steady

AI

DO

DI

Use the following table to identify the type of activity/function.

UI function 

Configuration

LED behaviour

Repeat mode

AI, AO, DI, DO

Colour for type

Trip mode

AI

Type single blink

Frequency mode

DI

Type single blink

1 in 2 out mode

Slave for any config.

Type double blink

Single blink = On 3s, Off 100ms          Double blink = On 3s, Off 100ms, On100ms, Off 100ms

5.3.2  Status indicator (S)

The status indicator is used to identify operating states and any fault/error conditions.  
The table below gives a listing of the possible states and how the LED indicates that state.

Condition

Configuration

LED display

Low state

DI and DO

Off

High state

DI and DO

Yellow

OK

AI and AO

Green

Tripped

AI in Trip mode

Yellow

LFD state

All modes

Yellow flash

Module Fault

All modes

Red

White

Magneta

- steady

- steady

Summary of Contents for MTL SUM5









































Reviews: