2
Note: Fixture weighs approximately 11lbs. Ensure grid location is rated for fixture
weight before moving to next step. If unsure use cable to support fixture to appropriate
support beam above fixture. See cable Support Installation.
6.
Place fixture in desired grid location (Fig. 6).
7.
Fully reconnect the quick disconnect by pushing the mating ends together (Fig. 7).
Note: Dimming leads should be wired at this point for 0-10V dimming applications. See
installing dimmer instructions below.
8.
Slide fixture JBOX cover to cover all wires on back of fixture ensuring the
disconnect and dimming wires are all completely inside fixture JBOX cover (Fig. 8).
9.
Orient 4 tabs on back of fixture over T-GRID by bending tabs up 90 degrees
perpendicular to back of fixture. Next bend tabs 90 degrees towards T-GRID frame (Fig. 9).
10.
Turn breaker on. Use wall switch to verify light turns on.
INSTALLING SUPPORT CABLES
1.
Remove cable lock by loosening set screw and pulling cable lock off cable (Fig 10).
2.
Slide cable through slot provide on back plate corner piece until the sphere bottoms out
against the slot (Fig 10).
3.
Slide cable lock onto cable. Loop open end of cable around support beam and back
through cable lock (Fig 10).
4.
Tighten cable lock set screw (Fig 10).
INSTALLING DIMMER
(For 0-10V Dimming)
• Using the wire termination provided on the dimming lead, combine the positive lead
from the dimmer with the positive lead (violet) connected to the dimming port (DIM +)
of the driver
• Combine the negative lead from the dimmer with the gray negative lead connected to
the (DIM -) dimming port of the driver using the wire termination that is fastened to the
end of the gray dimming lead
See Dimmer Compatibility
http://www.eaton.com/content/public/en/lighting/brands/
metalux.html
5-YEAR LIMITED WARRANTY
THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,
WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
Eaton warrants to customers that, for a period of five years from the date of purchase,
Eaton products will be free from defects in materials and workmanship. The obligation of
Eaton under this warranty is expressly limited to the provision of replacement products. This
warranty is extended only to the original purchaser of the product. A purchaser’s receipt or
other proof of date of original purchase acceptable to Eaton. This is required before warranty
performance shall be rendered. This warranty does not apply to Eaton products that have been
altered or repaired that have been subjected to neglect, abuse, misuse or accident (including
shipping damages). This warranty does not apply to products not manufactured by Eaton
which have been supplied, installed, and/or used in conjunction with Eaton products. Damage
to the product caused by replacement bulbs or corrosion or discoloration of brass components
are not covered by this warranty.
LIMITATION OF LIABILITY:
IN NO EVENT SHALL EATON BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES (REGARDLESS OF THE FORM OF ACTION, WHETHER IN CONTRACT,
STRICT LIABILITY, OR IN TORT INCLUDING NEGLIGENCE), NOR FOR LOST PROFITS; NOR SHALL
THE LIABILITY OF EATON FOR ANY CLAIMS OR DAMAGE ARISING OUT OF OR CONNECTED
WITH THESE TERMS OR THE MANUFACTURE, SALE, DELIVERY, USE, MAINTENANCE, REPAIR OR
MODIFICATION OF EATON PRODUCTS, OR SUPPLY OF ANY REPLACEMENT PARTS THEREFORE,
EXCEED THE PURCHASE PRICE OF EATON PRODUCTS GIVING RISE TO A CLAIM. NO LABOR
CHARGES WILL BE ACCEPTED TO REMOVE OR INSTALL FIXTURES.
To obtain warranty service, please contact Eaton, at 1-800-334-6871, press option 2 for
Customer Service, or via e-mail [email protected] and include the following
information:
• Name, address and telephone number
• Date and place of purchase
• Catalog and quantity purchase
• Detailed description of problem
All returned products must be accompanied by a Return Goods Authorization Number issued
by the Company and must be returned freight prepaid. Any product received without a Return
Goods Authorization Number from the Company will be refused. Eaton is not responsible for
merchandise damaged in transit. Repaired or replaced products shall be subject to the terms
of this warranty and are inspected when packed. Evident or concealed damage that is made
in transit should be reported at once to the carrier making the delivery and a claim filed
with them.
Reproductions of this document without prior written approval of Eaton are strictly prohibited.
For assistance, call 1-800-334-6871 or e-mail us at [email protected]
Printed in China
Fig. 5
Fig. 7
Fig. 6
Fig.9
T-Grid Folding Tab Instructions
Step 2
Step 1
Fig. 10
STEP 3
STEP 1
STEP 2
Fig. 8
Support Beam
