background image

 

Operating instructions ResistTel IP4/IP162 

03/22 

42 

Every call

 

Call protection is to be applied to all calls. 

External calls

 

Call protection is to be applied to external calls. 

Internal calls

 

Call protection is to be applied to internal calls. 

Out of office note

  Input parameter for entering a text message to the caller. 

Factory settings: 

Do not disturb:

 .......... 

Off

  // Call Protection Disabled 

Action:

.......... 

Ringing off

  // Acoustic sound call signaling turned off 

For:

.................... 

Every call

  // call protection applies to all calls 

Out of office note

 ..........   // Out of office message is empty 

5.1.4.4

 

Call waiting: On def. | On once | On mute | Off 

Main menu\User settings\

Call waiting

 

Call waiting selection parameter determines how the set should deal with a call that arrives during an 

active call. When call waiting is switched off, the device enters the caller in the call list for incoming calls 

and the caller immediately hears the "busy" signal tone. If, on the other hand, call waiting is activated, 

the call is first signaled visually and, if necessary, acoustically on the set and the called party decides 
how to proceed. He can reject the caller with key sequence 

 

 

or establish a connection to him with 

key sequence 

. During the signalling, the caller receives the signal tone "call waiting", in the case 

of rejection the signal tone "busy" or otherwise the desired speech connection.  
To change the setting, set the selection parameter described below to the value you want and, if you 
have changed the setting, press the menu key   repeatedly until the text display 

OK

 confirms that the 

change has been saved.  

Call waiting:

 ............ Selection parameter for determining the procedure for calls that arrive during 

active telephone calls. 

On def.

 

Call waiting is switched on, the call is signaled optically and acoustically. 
- Optical: Message 

1 call pending, subscriber XXXX

 in the display area. 

- Acoustic: Short, call-periodic emitted beep 

On once

 

Call waiting is switched on, the call is signaled optically and acoustically. 
- Optical: Message 

1 call pending, subscriber XXXX

 in the display area. 

- Acoustic: Long beep emitted once 

On mute

 

call waiting is switched on, the call is only signaled optically. 
- Optical: Message 

1 call pending, subscriber XXXX

 in the display area. 

- Acoustic: mute 

Off

 

Call waiting is switched off, the call is not signaled.  

Factory settings: 

Call waiting:

 ......

On def.

  // Call waiting switched on with optical and acoustic signaling. 

5.1.4.5

 

display phone no. : On |  Off 

Main menu\User settings\

display phone no.

 

Number transmission selection parameters determines whether the caller's number is transmitted to the 

called party in outgoing calls. When the telephone is idle, switched off phone number transmission is 
indicated by the pictogram   that is shown on the left in the footer of the display. 

To change the setting, set the selection parameter described below to the value you want and, if you 
have changed the setting, press the menu key   repeatedly until the text display 

OK

 confirms that the 

change has been saved.  

display phone no.:

 .... Selection parameter for switching the phone number transmission on and off 

On

 

Number transmission to the called party is switched on 

Off

 

Number transmission to the called party is switched off 

Summary of Contents for Malux solutions ResistTel IP162

































































Reviews: