Eaton HMIVU07CUNBE Instruction Sheet Download | Manualshive

Page: 1 / 16

background image

1

Remote Annunciator
Controller (RAC)
Instruction Sheet for
ATC-900 Controllers

Revision: 006

IB140010EN

Overview

1.0

The 7” RAC is a color touch-screen display with easy-to-use functions that provide a
powerful interface with up to 8 Automatic Transfer Switches equipped with the ATC-
900 controller. It supports serial RS-485 Modbus RTU and Modbus TCP/IP natively.
When using Ethernet to connect to an ATC-900, a serial-to-Ethernet Modbus gateway
is required such as the PXG-900 or the ELC-CAENET.

The 7” RAC Kit contains the following:

HMIVU07CUNBE (7” Color HMI Display)
IL04801003E (HMI Instruction Leaflet)
IB01602080E (Ethernet Setup Document)
ELC-PS01 or 02 (Optional 24VDC power supply)
IB140010EN (This Instruction Sheet)
66A8395, E, or EM (HMI Wiring Diagram)
66A8448H02 (HMI Interconnect Module – serial connections only)

1
2
3
...
»

Summary of Contents for HMIVU07CUNBE

















Reviews:

No comments

Related manuals for HMIVU07CUNBE

Brand: Waters Pages: 55

Brand: Paradox Pages: 2

Brand: Accel Pages: 8

SmartSwitch 6000

Brand: Cabletron Systems Pages: 76

Brand: Laars Pages: 28

Brand: IBA Pages: 29

Brand: Miller-Leaman Pages: 18

Brand: Procom Pages: 10

Brand: Vent-Axia Pages: 4

Brand: Partlow Pages: 49

Brand: Ascon tecnologic Pages: 11

Brand: ROBOT3T Pages: 21

Brand: StudioComm Pages: 61

Brand: Grundfos Pages: 80

Brand: Ubiquiti Pages: 16

Brand: DNF Controls Pages: 22

Brand: Matelec Pages: 2

Brand: KELCO Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands