Questions?/ Des questions?/ ¿Preguntas? 1-800-334-6871 [email protected]
1
Instruction Manual / Manuel d’instructions/ Instrucciones
PACKAGING CONTENTS /CONTENU DE L’EMBALLAGE/CONTENIDO DEL PAQUETE
WIRING YOUR FIXTURE
1.
Turn the power OFF at main fuse/breaker box.
2.
Connect the black fixture wire to the black supply wire (hot). Secure with a wire connector (F).
3.
Connect the white fixture wire to the white supply wire (neutral). Secure with a wire
connector (F).
4
. Connect the bare ground wire on the mounting bracket (D) to an appropriate supply
ground or grounded junction box. Secure with a wire connector (F).
NOTE:
Be careful to connect the wires correctly. Make sure no bare strands of wire are
sticking out of the wire connectors (F).
INSTALLING THE BULB
1.
Rotate the lamp and line up the pins on the bulb (C) with the holes in the socket.
2.
Snap the bulb (C) securely into the socket.
NOTE:
When replacing the bulb (C), you must always use the same wattage and type of bulb
that was originally supplied with the fixture. Failure to do so could result in damage to the
fixture and bulb (C). This will void the warranty. Always turn OFF or disconnect power before
servicing to reduce risk of electrical shock.
MANUAL OPERATION
NOTE:
You may choose to override the photo control.
This will allow you to control the fixture from a wall
switch without the dusk-to-dawn feature.
1. Snap the photo control cover (H) over the photo
control on the face of the fixture (Fig. 1).
ENGLISH
A.
Fixture housing
Alojamiento del
portalámparas
Boîtier de l’appareil
d’éclairage
D.
Adjustable mounting bracket, knobs and screws
Soporte de montaje ajustable, perillas y tornillos
Support de montage réglable, boutons et vis
F. (3) Wire connectors
(3) Conectores de cable
(3) Serre-fils
G. (2) #6 and (2) #8 screws
(2) Tornillos #6 y (2) tornillos #8
(2) #6 et (2) vis #8
H. Photo control cover (optional)
Cubierta del control de foto celda (opcional)
Couvercle de l’interrupteur photo-électrique
(facultatif)
B.
Lens (installed on fixture)
Lente (instalado en el artefacto)
Lentille (installée sur l’appareil)
C.
Bulb (inside fixture)
Lámpara (dentro del
artefacto)
Bombilla (luminaire
intérieur)
E.
Lens screw (installed in fixture)
Tornillo del lente (instalado en
el artefacto)
Vis de lentille (installée dans
l’appareil)
ITEMS REQUIRED
(Purchase separately)
• Phillips screwdriver
• Flat head screwdriver
• Weatherproof silicone caulk
IMPORTANT SAFETY INSTRUCTIONS
When using product, basic precautions should always be followed, including the following:
• Heed all warnings, including below warnings AND those included on product.
• Save these instructions and warnings.
• For outdoor use only.
• cULus LISTED for wet location.
• Your fixture is prewired and preassembled for easy installation.
• Do not use SBCFL lamps identified “NOT FOR TOTALLY ENCLOSED LUMINAIRE”
Notice: Lamps contain mercury. Dispose according to local, state, or federal laws.
For more information, visit: www.lamprecycle.org.
• Read and follow these instructions.
• Risk of fire/electric shock. If not qualified, consult an electrician.
• Disconnect power at fuse or circuit breaker before installing or servicing.
1.
Turn power OFF at main breaker that runs to the junction box where fixture will be installed.
2.
Attach adjustable mounting bracket (D) to junction box on wall using two of the mounting
plate screws provided (G). Either the #6 or #8 screws (G) provided will fit most standard
junction boxes. Position the bracket (D) so that the mounting studs (D) for the fixture are
horizontal. Tighten the rotation screws (D) on the bracket.
3.
Loosen lens screw (E) in the bottom of the fixture completely out and remove the lens
and bulb.
4
. Wire the fixture as described in “Wiring your fixture”.
5.
Position the fixture so that the bracket screws pass through the backplate of the fixture
housing (A). Tighten the housing (A) to the mounting bracket (D) with the knobs (D)
provided. Make sure your fixture is straight. Mounting bracket (D) does swivel so you can
adjust to get fixture straight.
6.
Install the bulb (C) as described in “Installing the bulb” and put lens (B) back onto fixture
housing (A). Insert lens screw (E) and tighten to secure the lens. Be sure the lens edges
and lens screw tab are fully seated on the inside of the fixture housing (A).
7.
Add silicone caulk around fixture to help maintain a weather resistant seal.
8.
Turn power back ON. Bulb (C) should glow dimly at first building to full power in 1-2 minutes.
NOTE:
During daytime installation, the bulb should turn off after 45 seconds to one minute.
This is normal operation. The bulb will restart at night and operate until dawn.
Fig. 1
H
WARNING
TROUBLESHOOTING
Problem
Light Does
Not Come On
Light Comes
On For Only A
Few Seconds
Cause / Solution
No power to the fixture.
• Check if circuit breaker tripped.
• Confirm wall switch is ON.
Bulb is not screwed in properly.
• Confirm bulb is seated properly. (Be careful not to overtighten)
Bulb is faulty.
• Replace bulb.
Wiring to the unit is loose.
• Confirm fixture is properly grounded.
Caution: Turn power OFF before checking.
Fixture is sensing daylight
• Cover photo control. Unit will switch OFF within a few minutes.
Light sensor is sensing reflected light.
• Cover light sensor with electrician’s tape. Wait 2-3 minutes to
see if light turns ON. If it does, fixture is receiving reflected light.
Partially cover the light sensor to block out the reflected light.
FW26PCI
FW26PCIH
FW26PCIW
