background image

1

Questions?/ Des questions?/ ¿Preguntas? 1-800-334-6871 [email protected]

Instruction Manual / Manuel d’instructions/ Instrucciones

MOUNTING YOUR FIXTURE

NOTE:

 This fixture is intended to be conduit connected 

to a properly installed and properly grounded metal  

weatherproof junction box (not included). All conduit  

connectors, conduit, and junction boxes (sold separately)  

should be UL Listed suitable for wet locations.

1.

   Using the pattern on the box, mark and drill holes 

for mounting. 

NOTE: 

Mount this fixture in an upright position.

2.

   Install the two bottom mounting screws (E) first, 

leaving enough room between the mounting  

screws and the mounting surface to accommodate 

mounting the fixture.

3.

   Screw the top mounting screw (E) into the predrilled 

hole and back the screw out. This will leave the hole 

threaded and make installation of the fixture easier.

4.

   Remove access cover (D) from parts bag.

5.

   Install the first conduit connector and conduit

(sold separately) into the access cover (D).

6.  

Feed supply wires into conduit and make wiring 

connections as described in “Wiring Your Fixture”.

7.

   Attach access cover (D) to the light fixture (A)

using the two access cover mounting screws (F) 

provided (Fig. 1).

NOTE:

 Make sure all wiring is placed into the arm 

prior to tightening the access cover screws (F).

8. 

Using the three mounting screws (E) provided, bolt 

the housing (A) to the mounting surface.

9. 

Connect second conduit and conduit connector at 

the junction box (Fig. 2).

10. 

Fasten lens assembly (B) to housing (A) using the 

two lens assembly lock screws (G) and two washers 

(H) provided (Fig. 3).

NOTE: 

Washers must be used to keep the lens in place.

WIRING YOUR FIXTURE

1.  Turn off the power at the main fuse/breaker box.
2. 

Attach ground wire that is attached to fixture 

housing (A) to the junction box earth ground wire.

3. 

Connect the black fixture wire to the black supply wire (hot). Attach UL approved wire  

 

connector (sold separately).

4. 

Connect the white fixture wire to the white supply wire (neutral). Attach UL approved wire  

 

connector (sold separately).

NOTE:

 Be careful to connect the wires correctly. Make sure no bare strands of wire extend 

from the wire nut or other approved wire connectors (sold separately).

PACKAGING CONTENTS /CONTENU DE L’EMBALLAGE/CONTENIDO DEL PAQUETE

ITEMS REQUIRED

 

(Purchase separately)

•  Phillips screwdriver
•  Adjustable wrench
•  Drill with 3/16 in. drill bit
•  1/2 in. diameter flexible conduit (if applicable, length depends on application)
•  1/2 in. watertight conduit connectors (if applicable)
•  Wire connectors

IMPORTANT SAFETY INSTRUCTIONS

  When using product, basic precautions should always be followed, including the following:

•  Read and follow these instructions.
•  Heed all warnings, including below warnings AND those included on product.
•  Save these instructions and warnings.
•  For outdoor use only.
•  cULus LISTED for wet location use.

•  Disconnect at fuse or circuit breaker before installing or servicing.
•  Disconnect power and allow fixture to cool before changing bulb or handling fixture.
•  Edges may cut. Handle with care.

     Notice: Lamps contain mercury, dispose according to local, state, or federal laws. 

     For more information, visit: www.lamprecycle.org.

CAUTION

•  Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids 

the warranty.

•  Fixture should be installed by persons with experience in household wiring or by a 

qualified electrician. The electrical system, and the method of electrically connecting 

the fixture to it, must be in accordance with the National Electrical Code and local 

building codes.

•  Always use same wattage and type of bulb that was included with the fixture. Failure 

to do so will void the warranty. See fixture for wattage.

•  Upside down installation can result in overheating or accumulation of water in fixture.

Install right side up.

•  MINIMUM 90° C SUPPLY CONDUCTORS.
•  This device complies with Part 18 of the FCC Rules.
•  This product may cause interference to radio equipment and should not be installed 

near maritime safety communications equipment, ships at sea or other critical  

navigation or communications equipment operating between 0.45-30 MHz.

AL6501FL

AL6501FLH

A.

  Fixture housing with 

  light sensor
  Boîtier du luminaire avec  
  détecteur de lumière
  Alojamiento del accesorio 
  con detector de luz

 ENGLISH

E.

  (3) Mounting screws

  (3) Vis de montage  

(3) Tornillos de montaje 

B. 

One-piece lens 

 assembly
  Ensemble de lentille  
  d’une seule pièce
  Ensamblado del 
  lente de una sola pieza

C. 

65 watt fluorescent bulb 

  Ampoule fluorescente de  
  65 watts
  Bombilla fluorescente 
  de 65 vatios

D.

   Access cover

  Cache d’accès 

Cubierta de  
acceso

G.

  (2) Lens assembly lock screws

   (2) Vis de blocage pour assem   
   blage lentille   
   (2) Tornillos de fijación del
   ensamblado del lente

F.

  (2) Access cover mounting screws

  (attached to fixture)
  (2) Vis de montage du cache d’accès 

(attached to fixture) 
(2) Tornillos de la cubierta de acceso  
(conectado al accesorio)

H.

   (2) Washers

   (2) Arandelas
   (2) Rondelles

Fig. 2

Conduit 

Junction 

box

Conduit 

connector

A

Fig. 1

F

F

D

A

Fig. 3

A

B

G

H

WARNING

Summary of Contents for HALO AL6501FL






Reviews: