background image

Important  Note:  If  the  UPS  is  used  in  Single  Mode,  JP1  and  JP2  must  be 
connected  by  10AWG (6mm

2

). If the  UPS  is  used  in  Parallel  Mode, the  Jumper 

between JP1 and JP2 must be removed.

 

 

Option: 2 

 
 
 
 
 
 
 

Connect Output Line 1 and Neutral2 by 10AWG (6mm

2

) for 240V / 6KVA Load. 

Important  Note:  If  the  UPS  is  used  in  Single  Mode,  JP1  and  JP2  must  be 
connected  by  10AWG (6mm

2

). If the  UPS  is  used  in  Parallel  Mode, the  Jumper 

between JP1 and JP2 must be removed. 

 

2.3 Operating procedure for connecting the long backup                                                                                                                                                                                                                       

time model UPS with the external battery   

1.

  The  nominal  DC  voltage  of  external  battery  pack  is  240VDC. 

Each battery pack consists of 20 pieces of 12V maintenance free 
batteries in series. To achieve longer back time, it is possible to 
connect multi-battery packs, but the principle of 

same voltage, 

same type

 should be strictly followed.

 

2.

  The connector of the external battery cable is used to plug into 

the  external  battery  socket  of  the  UPS,  the  other  end  of  the 
external  battery  cable  is  made  of  three  open  wires  with  ring 
terminals  to  connect  with  the  external  battery  pack(s).  The 
procedure    of  installing  battery  bank  should  be  complied  with 
strictly. Otherwise you may encounter the  hazardous of electric 
shock.

 

Connection Details of Output Terminals.

 

 

Summary of Contents for DX 10000L






























Reviews: