background image

42

Instruction Book    

IB182917EN   September 2018   www.eaton.com

DHP-VR

+

VR-Series

+

 Replacement Circuit Breaker

SECTION 7:   REPLACEMENT PARTS

7.1   GENERAL

In order to minimize production downtime, it is recommended that 

an adequate quantity of spare parts be carried in stock. The quantity 

will vary from customer to customer, depending upon the service 

severity and continuity requirements. Each customer should develop 

his own level based on operating experience. However, when 

establishing a new operating record, it is a good practice to stock 

one set of control components for every six circuit breakers of the 

same control voltage. This quantity should be adjusted with time and 

frequency of operation of the circuit breakers.

1.

ANTI-PUMP (Y) RELAY

(48Vdc)

(125Vdc)

(250Vdc)

(120Vac)

(240Vac)

94C9525H01

94C9525H02

94C9525H03

94C9525H04

94C9525H05

2.

RECTIFIER

Rectifier

94C9525G09

3.

SPRING CHARGING MOTOR

(48Vdc)

(125Vdc)

(250Vdc / 240Vac)

94C9525G10

94C9525G11

94C9525G12

4.

AUXILIARY SWITCH

Circuit Breaker Auxiliary 

Switch 

94C9525G13

5.

POSITION SWITCH

Circuit Breaker Position 

Switch PS1

94C9525H06

6.

POSITION SWITCH

Circuit Breaker Position 

Switch PS2

94C9525H07

7.

LATCH CHECK SWITCH

Latch Check Switch (LC)

94C9525H08

8.

MOTOR CUTOFF SWITCHES

(

LS) 

94C9525G15

9.

SPRING RELEASE COILS / 

SHUNT TRIPS

24Vdc

48Vdc

125Vdc / 120Vac

250Vdc / 240Vac

94C9525G16

94C9525G17

94C9525G18

94C9525G19

10.

CONTROL COMPONENTS KIT

48Vdc

125Vdc

250Vdc

120Vac-C/M 48Vdc-T

240Vac-C/M 48Vdc-T

120Vac-C/M 120Vac-CT

240Vac-C/M 240Vac-CT

94C9525G01

94C9525G02

94C9525G03

94C9525G04

94C9525G05

94C9525G06

94C9525G07

7.2   ORDERING INSTRUCTIONS

a. The style numbers in Table 7.1 should be sufficient to purchase 

control components for most applications. Some circuit breakers 

have special control schemes. Supply complete nameplate 

information for verification or if additional components are 

needed.

b. Specify the method of shipping desired.
c. Send all orders or correspondence to the nearest Eaton sales 

office or contact the PBC direct at 1-877-276-9379.

d. Include negotiation number with order when applicable.

Tablt 7.1  Common Rtplactmtnt Parts - Dtscriptions and Stylt Numbtrs

Summary of Contents for DHP VR + Series












































Reviews: