background image

17

Instruction Book    

IB182917EN   September 2018   www.eaton.com

DHP-VR

+

VR-Series

+

 Replacement Circuit Breaker

Figure 4.10.d shows the circuit breaker in the closed state after the 

closing springs have been recharged. The recharging of the spring 

rotates the closing cam one half turn. In this position the main link 

roller rides on the cylindrical portion of the cam, and the main link 

does not move out of position.

4.3.3   TRIPPING OPERATION

When the trip bar “D” shaft (Figure 4.10.b, Item 9) is turned by 

movement of the shunt trip clapper (11), the trip latch will slip past 

the straight cut portion of the trip bar shaft and will allow the banana 

link and main link roller to lower. The energy of the opening spring 

and contact loading springs is released to open the main contacts. 

The mechanism is in the state illustrated (Figure 4.10.b) after the 

circuit breaker is tripped open.

4.3.4   TRIP-FREE OPERATION

When the manual trip button is held depressed, any attempt to close 

the circuit breaker results in the closing springs discharging without 

movement of the pole shaft or vacuum interrupter stem.

4.4   CONTROL SCHEMES

There are two basic control schemes for the VR-Series

+

 circuit 

breaker elements, one for dc control and one for ac control voltages 

(Figure 4.4). Specific customer order wiring schematics and 

diagrams are included with each circuit breaker.
There may be different control voltages or more than one tripping 

device, but the principal mode of operation is as follows:
As soon as the control power is applied, the spring charging motor 

automatically starts charging the closing spring. When the springs 

are charged, the motor cut off LS1/bb switch turns the motor off. 

The circuit breaker may be closed by closing the control switch close 

(CS/C) contact. Automatically upon closing of the circuit breaker, the 

motor starts charging the closing springs. The circuit breaker may be 

tripped any time by closing the control switch (CS/T) contacts.
Note the position switch (PS1) contact in the spring release circuit 

in the scheme. This contact remains closed while the circuit breaker 

is being racked between the ‘Test’ and ‘Connect’ positions for 

VR-Series

+

 circuit breakers. Consequently, it prevents the circuit 

breaker from closing automatically, even though the control close 

contact may have been closed while the circuit breaker is racked to 

the ‘Connect’ position.
When the CS/C contact is closed, the SR closes the circuit breaker. 

If the CS/C contact is maintained after the circuit breaker closes, the 

Y relay is picked up. The Y/a contact seals in Y until CS/C is opened. 

The Y/b contact opens the SR circuit, so that even though the circuit 

breaker would subsequently open, it could not be reclosed before 

CS/C was released and remade. This is the anti-pump function.

4.4.1   TIMING

The opening and closing times for the circuit breakers vary 

depending upon the control voltage, power rating, environment and 

test equipment. Differences in timing are expected between initial 

factory measurements and field inspections. Circuit breaker timing 

can be measured by service personnel using available equipment 

before installation and in conjunction with regular maintenance 

periods to assist in tracking the general health of the circuit breaker. 

Typical ranges as observed using nominal control voltages are listed 

in Table 4.

Tablt 4. Timt Ptr Evtnt

Event

Milliseconds

Closing Time

(From Initiation of Close Signal to Contact Make)

45 - 60

Opening Time

(Initiation of Trip Signal to Contact Break)

30 - 38

Reclosing Time

(Initiation of Trip Signal to Contact Make)

140 - 165

otte:

N

Valuts art typical at nominal rattd control voltagt(s).

4.5   SECONDARY DISCONNECT CONTACT BLOCK

The circuit breaker control wiring is arranged for draw-out 

disconnecting by means of a 15 point male plug arranged to connect 

to a female receptacle mounted in the rear of the existing DHP 

circuit breaker compartment. The secondary disconnect contact 

block is mounted on a movable bracket on the left side of the circuit 

breaker truck (Figures 4.3). This permits it to be extended to the 

rear while the circuit breaker is in the ‘Test’ position to connect with 

the stationary receptacle in the circuit breaker compartment so that 

the control circuits are completed. Control wiring terminates first at 

terminal block(s) mounted on the circuit breaker truck, and continues 

from the terminal blocks to the male contact plug.
Normally the secondary disconnect contact is held stationary relative 

to the circuit breaker chassis. This is accomplished by a hinged joint 

in the hand operating rod which acts on the edge of the lower front 

truck panel to hold the assembly in position.
To engage the secondary disconnect contact while the circuit 

breaker is in the ‘Test’ position, lift the handle on the front left hand 

side of the circuit breaker chassis to a horizontal position. Once the 

rod is pointing straight out from the circuit breaker, push it manually 

to the rear until the secondaries are initially engaged. At this point, 

the small horizontal pin in the handle will have engaged two slots in 

the lever, which is pivoted immediately above the handle. To insure 

complete secondary engagement, push down firmly on the curved 

end of the lever as far as it will go, using a foot or hand (Figure 5.7). 

When using a foot, care should be taken not to bend the lever by 

using excessive force.

Figurt 4.3. Stcondary Disconntct Contact Block  

 

(Exttndtd Position) 

Summary of Contents for DHP VR + Series












































Reviews: