background image

1 0

EATON CORPORATION  Cutler-Hammer

 Information Sheets  70C1486H01

Eaton Electrical, Inc.
1000 Cherrington Parkway
Moon Township, PA  15108-4312
United States
Tel.: 1-800-525-2000
www.EatonElectrical.com

© 2006 Eaton Corporation

All Rights Reserved

Printed in USA

Publication No.  I.S.70C1486H01

July 2006

DISCLAIMER OF WARRANTIES AND
LIMITATION OF LIABILITY

The information recommendations, descriptions and safety
notations in this document are based on Eaton’s experi-
ence and judgment and may not cover all contingencies.  If
further information is required an Eaton sales office should
be consulted.

Sale of the product shown in this literature is subject to the
terms and conditions outlined in appropriate Eaton Electri-
cal Inc. selling policies or other contractual agreement be-
tween Eaton and the purchaser.

THERE ARE NO UNDERSTANDINGS, AGREEMENTS,
WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING
WARRANTIES OF FITNESS FOR A PARTICULAR PUR-
POSE OR MERCHANTABILITY, OTHER THAN THOSE
SPECIFICALLY SET OUT IN ANY EXISTING CONTRACT
BETWEEN THE PARTIES.  ANY SUCH CONTRACT
STATES THE ENTIRE OBLIGATION OF EATON ELECTRI-
CAL INC.  THE CONTENTS OF THIS DOCUMENT SHALL
NOT BECOME PART OF OR MODIFY ANY CONTRACT
BETWEEN THE PARTIES.

IN NO EVENT WILL EATON ELECTRICAL INC. BE
RESPONSIBLE TO THE PURCHASER OR USER IN
CONTRACT, IN TORT (INCLUDING NEGLIGENCE),
STRICT LIABILITY OR OTHERWISE FOR ANY SPECIAL,
INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGE
OR LOSS WHATSOEVER, INCLUDING BUT NOT
LIMITED TO DAMAGE TO OR LOSS OF USE OF
EQUIPMENT, PLANT OR POWER SYSTEM, LOSS OF
PROFITS OR REVENUES, OR CLAIMS AGAINST THE
PURCHASER OR USER BY ITS CUSTOMERS
RESULTING FROM THE USE OF THE PRODUCTS OR
INFORMATION,  RECOMMENDATIONS AND
DESCRIPTIONS CONTAINED HEREIN.

Cutler-Hammer is a federally

registered trademark of Eaton

Corporation. Digitrip is a  trade-

mark of Eaton Corporation.

Summary of Contents for Cutler-Hammer Digitrip 1150











Reviews: