DRAFT - 28 July 2014
The given data is only intended as a product
description and should not be regarded as a legal
warranty of properties or guarantee. In the interest
of further technical developments, we reserve the
right to make design changes.
2
MTL trunk surge module
January 2017
Eaton Electric Limited,
Great Marlings, Butterfield, Luton
Beds, LU2 8DL, UK.
Tel: + 44 (0)1582 723633 Fax: + 44 (0)1582 422283
E-mail: [email protected]
www.mtl-inst.com
© 2017 Eaton
All Rights Reserved
Publication No. INS9376 Rev 2 170117
January 2017
EUROPE (EMEA):
+44 (0)1582 723633
[email protected]
THE AMERICAS:
+1 800 835 7075
[email protected]
ASIA-PACIFIC:
+65 6 645 9888
[email protected]
DRAFT - 28 July 2014
The given data is only intended as a product
description and should not be regarded as a legal
warranty of properties or guarantee. In the interest
of further technical developments, we reserve the
right to make design changes.
MTL trunk surge module
January 2017
Eaton Electric Limited,
Great Marlings, Butterfield, Luton
Beds, LU2 8DL, UK.
Tel: + 44 (0)1582 723633 Fax: + 44 (0)1582 422283
E-mail: [email protected]
www.mtl-inst.com
© 2017 Eaton
All Rights Reserved
Publication No. INS9376 Rev 2 170117
January 2017
EUROPE (EMEA):
+44 (0)1582 723633
[email protected]
THE AMERICAS:
+1 800 835 7075
[email protected]
ASIA-PACIFIC:
+65 6 645 9888
[email protected]
ATEX and IECEx Safety Instructions for 9376-SP Trunk Surge
Module
The following information is in accordance with the
Essential Health and Safety Requirements (Annex II) of the
EU Directive 2014/34/EU [the ATEX Directive - safety of apparatus]
and is provided for those locations where such requirements are
applicable.
General
a)
This module must only be installed, operated and
maintained by competent personnel. Such personnel shall
have undergone training, which included instruction on the
various types of protection and installation practices, the
relevant rules and regulations, and on the general principles
of area classification. Appropriate refresher training shall be
given on a regular basis. [See clause 4.2 of EN 60079-17].
b)
This module has been designed to provide protection
against all the relevant additional hazards referred to in
Annex II of the directive, such as those in clause 1.2.7.
c)
This module has been designed to meet the requirements of
EN 60079-0, EN 60079-1, EN 60079-7, EN 60079-18.
Installation
d)
The installation must comply with the appropriate European,
national and local regulations, which may include reference
to the IEC code of practice IEC 60079-14. In addition,
particular industries or end users may have specific
requirements relating to the safety of their installations and
these requirements should also be met. For the majority of
installations the Directive 1999/92/EC [the ATEX Directive -
safety of installations] is also applicable.
e)
This module can be mounted in a Safe area or a Zone 2 or
Zone 1 hazardous area. When mounted in a Zone 2 or Zone
1 location the module must be provided with an enclosure,
which offers an additional degree of protection appropriate
to the area classification.
f)
Unless already protected by design, this module must be
protected by a suitable enclosure against:
i) mechanical and thermal stresses
in excess of those noted in the certification documentation
and the product specification.
ii) aggressive substances, excessive dust, moisture and other
contaminants.
Read also the Schedule of Limitations (below) for any additional or
more specific information.
Schedule of Limitations
1)
The 9376-SP Trunk Surge Protector must be housed in an
appropriately certified Ex e enclosure.
2)
The 9376-SP Trunk Surge Protector must plug into
equipment that uses the socket part of the connector
covered by certificate TUV09ATEX555354U.
3)
Due to the presence of transient protection components
between the fieldbus and earth connections, the
9376-SP Trunk Surge Protector will not withstand a 500V
a.c. dielectric strength test. This must be taken into account
during installation.
4)
The ambient temperature must not exeed +75°C.
5)
The 9376-SP Trunk Surge Protector shall only be powered
from supplies conforming to IEC 61158.
6)
The 9376-SP Trunk Surge Protector shall only be connected
into equipment that causes the secondary latching
connector to limit movement before the live-demateable
connector plug and socket metal parts separate by over
1.9mm.
Inspection and maintenance
Inspection and maintenance should be carried out in accordance
with European, national and local regulations which may refer to
the IEC standard IEC 60079-17. In addition specific industries or
end users may have specific requirements which should also be
met.
Repair
This module cannot be repaired by the user and must be
replaced with an equivalent certified product.
Marking
Each module is marked in compliance with the above
Directive and CE marked with the Notified Body
Identification Number.
This information applies to modules manufactured during or after
the year 2010.
ATEX and IECEx Safety Instructions for 9376-SP Trunk Surge
Module
The following information is in accordance with the
Essential Health and Safety Requirements (Annex II) of the
EU Directive 2014/34/EU [the ATEX Directive - safety of apparatus]
and is provided for those locations where such requirements are
applicable.
General
a)
This module must only be installed, operated and
maintained by competent personnel. Such personnel shall
have undergone training, which included instruction on the
various types of protection and installation practices, the
relevant rules and regulations, and on the general principles
of area classification. Appropriate refresher training shall be
given on a regular basis. [See clause 4.2 of EN 60079-17].
b)
This module has been designed to provide protection
against all the relevant additional hazards referred to in
Annex II of the directive, such as those in clause 1.2.7.
c)
This module has been designed to meet the requirements of
EN 60079-0, EN 60079-1, EN 60079-7, EN 60079-18.
Installation
d)
The installation must comply with the appropriate European,
national and local regulations, which may include reference
to the IEC code of practice IEC 60079-14. In addition,
particular industries or end users may have specific
requirements relating to the safety of their installations and
these requirements should also be met. For the majority of
installations the Directive 1999/92/EC [the ATEX Directive -
safety of installations] is also applicable.
e)
This module can be mounted in a Safe area or a Zone 2 or
Zone 1 hazardous area. When mounted in a Zone 2 or Zone
1 location the module must be provided with an enclosure,
which offers an additional degree of protection appropriate
to the area classification.
f)
Unless already protected by design, this module must be
protected by a suitable enclosure against:
i) mechanical and thermal stresses
in excess of those noted in the certification documentation
and the product specification.
ii) aggressive substances, excessive dust, moisture and other
contaminants.
Read also the Schedule of Limitations (below) for any additional or
more specific information.
Schedule of Limitations
1)
The 9376-SP Trunk Surge Protector must be housed in an
appropriately certified Ex e enclosure.
2)
The 9376-SP Trunk Surge Protector must plug into
equipment that uses the socket part of the connector
covered by certificate TUV09ATEX555354U.
3)
Due to the presence of transient protection components
between the fieldbus and earth connections, the
9376-SP Trunk Surge Protector will not withstand a 500V
a.c. dielectric strength test. This must be taken into account
during installation.
4)
The ambient temperature must not exeed +75°C.
5)
The 9376-SP Trunk Surge Protector shall only be powered
from supplies conforming to IEC 61158.
6)
The 9376-SP Trunk Surge Protector shall only be connected
into equipment that causes the secondary latching
connector to limit movement before the live-demateable
connector plug and socket metal parts separate by over
1.9mm.
Inspection and maintenance
Inspection and maintenance should be carried out in accordance
with European, national and local regulations which may refer to
the IEC standard IEC 60079-17. In addition specific industries or
end users may have specific requirements which should also be
met.
Repair
This module cannot be repaired by the user and must be
replaced with an equivalent certified product.
Marking
Each module is marked in compliance with the above
Directive and CE marked with the Notified Body
Identification Number.
This information applies to modules manufactured during or after
the year 2010.
