background image

Step 9.
Install compression connector

ote:

N

Refer to the chart supplied with the crimp 

connector for tool and die to be used.

 

Wire brush conductor (aluminum only).

 

Remove protective cap from compression connector.

 

Insert conductor completely into compression connector 

and rotate connector to distribute inhibitor.

ote:

N

Connector must be fully seated on cable conductor.

 

Align flats of connector and apparatus bushing for 

minimum conductor strain.

 

Make first crimp 1/2" (13 mm) below shoulder of 

compression connector. (Refer to Figure 22).

 

Rotate each successive crimp 90° on compression 

connector and allow 1/8" (3 mm) between crimps.

 

Wipe excess inhibitor from connector and adapter 

surfaces.

Step 10.
Check  di men sions

 

Check length from end of com pres sion con nec tor to top 

of cable adapter.

 

Length should be be tween 6.50-7.25" (165 - 184 mm). (Re-

fer to Fig ure 23.)

Figure 23. Line illustration for dimensional check.

6.50-7.25"

(165-184 mm)

Cable 

Adapter

Concentric 

Neutral Wires

Tape 

Marker

Compression 

Connector

Figure 22. Line illustration of crimping area.

Bushing

Shoulder

Tool

Crimping 

Area

Cable 

Adapter

10

600 A 15/25 kV class BOL-T connector assembly installation instructions for 

  MN650005EN   February 2015  

Summary of Contents for COOPER POWER SERIES





















Reviews: