manualshive.com logo in svg

Eaton Char-Lynn VersaSteer 10 Series, Parts And Repair Information, Page: 16 / 16

Share
Download
Eaton Char-Lynn VersaSteer 10 Series Parts And Repair Information Download Page 16

© 2005 Eaton Corporation
All Rights Reserved
Printed in USA
Document No. C-STCU-TS006-E
June 2005

Eaton

14615 Lone Oak Road
Eden Prairie, MN 55344
USA
Tel: 952 937-9800
Fax: 952 974-7722
www.hydraulics.eaton.com

Eaton

Dr.-Reckeweg-Str. 1
D-76532 Baden-Baden
Germany
Tel: (49) 7221 682-0
Fax: (49) 7221 682-788

Eaton

20 Rosamond Road
Footscray
Victoria 3011
Australia
Tel: (61) 3 9319 8222
Fax: (61) 3 9318 5714

34. Install 7 dry cap screws in 

end cap. Pretighten cap 
screws to 17Nm [150 lb-in], 
then torque screws to 
28-34 Nm [250-300 lb-in] in 
sequence shown in 
figure 29.

1

3

5

7

2

4

6

Figure 29

Assembly

Figure 28

31 Install back-up ring and seal 

ring in gerotor star.

32. Lubricate and install 72,6 mm 

[2.86 in.] ID seal in gerotor 
(meter).

33. Install end cap on gerotor, 

aligning holes.

Screw, Cap, Hex Head

Cap, End

Seal

Seal, Ring (metal)

Low Slip
Sealed
Gerotor
Star 

Ring, Back-up (rubber)

Gerotor

Groove cross section
w/ rings

Summary of Contents for Char-Lynn VersaSteer 10 Series

















Reviews:

No comments