background image

Operating Instructions

10

6.7 Individual Zone Test

• This function is only available at access level 2.

•  This function will allow individual zones to be placed in the

zone test mode.

• Enter the access code 3112

• Press “Test” button (2).

•  The zone currently in test mode will have its associated

disabled indicator lit and all zones not in test mode will
have their associated disabled indicators unlit.

• The function always starts at Zone 1.

•  When an item is selected for test mode its disable

indicator will change from unlit to lit.

•  When an item is selected for normal operation its disable

indicator will change from lit to unlit.

•  Press the following button sequences for the required test

 mode/normal operation:

• Pressing “Select” button (3) will accept the selected test

zone and exit back to Access Level 1. The Test indicator
will remain lit and the zone disabled indicator will also
remain 

lit.

•  When a fi re detection device or manual call point is

activated in the zone under test it will sound all fi re alarm
devices for 3 seconds and then will automatically silence.

• Any fi re condition detected in any other zone will place the

system into full alarm condition and the fi re alarm devices
will activate continuously.

•  To end the individual test mode the above selection

instructions should be carried out and the zone disabled
indicator changed to the unlit state.

6.8 Lamp Test

• This function is available at access level 2.

• Enter the access code 3112.

• Press “Indicator Test” button (3).

•  Each indicator on the front of the panel will turn on in turn

and then turn off in turn (excluding the Power On indicator).

•  This function will immediately exit back to Access Level 1.

Item  

2-Zone

4-Zone

8-Zone

Zone 1

3

3

3

Zone 2 

2 + 3 

2 + 3 

2 + 3 

Zone 3 

2 (2 times) + 3 

2 (2 times) + 3 

Zone 4 

2 (3 times) + 3 

2 (3 times) + 3 

Zone 5 

2 (4 times) + 3 

Zone 6 

2 (5 times) + 3 

Zone 7 

2 (6 times) + 3 

Zone 8 

2 (7 times) + 3

March

 2016 

  www.eaton.com 

EATON BiWire Flexi User Manual   (

PR215-216-519-03 15-03-16

, PINSTFLEXIUSER)

Summary of Contents for BiWire Flexi

















Reviews: