2
3.
Hang one end of the support hook onto the mounting
bracket and hang the light fixture on the other end of
the support hook (Fig. 5).
4.
Connect fixture black wire to house black wire and
fixture white wire to house white wire by firmly
pushing into quick connect wiring connectors
(Fig. 6).
5.
Connect house ground wire and fixture ground wire
by firmly pushing into quick connect wiring
connector. (Fig. 6). Attach fixture (A) to the mounting
bracket (B) using (2) #8 x 1-1/4 in. screws (F)
pre-attached to the canopy. Be sure no loose wires
remain sticking out from underneath the coverplate.
Insert the decorative screw cover caps (G) into the
screw holes on the coverplate for a finished appear-
ance (Fig. 6).
6.
Adjust light fixture to desired postion by loosening the lower arm jam nut and the
thumbscrew on the upper arm. Move the head to aim and retighten the thumbscrew and
jam nut.
7.
Apply silicone caulk around the edges of the coverplate and jam nuts at the base of the
adjustment arms to provide a watertight seal from rain and moisture.
8.
Turn on power at main fuse/breaker box.
TROUBLESHOOTING
5-YEAR LIMITED WARRANTY
THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,
WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
Eaton warrants to customers that, for a period of five years from the date of purchase, Eaton
products will be free from defects in materials and workmanship. The obligation of Eaton
under this warranty is expressly limited to the provision of replacement products. This war-
ranty is extended only to the original purchaser of the product. A purchaser’s receipt or other
proof of date of original purchase acceptable to Eaton. This is required before warranty per-
formance shall be rendered. This warranty does not apply to Eaton products that have been
altered or repaired that have been subjected to neglect, abuse, misuse or accident (including
shipping damages). This warranty does not apply to products not manufactured by Eaton
which have been supplied, installed, and/or used in conjunction with Eaton products. Damage
to the product caused by replacement bulbs or corrosion or discoloration of brass components
are not covered by this warranty.
LIMITATION OF LIABILITY:
IN NO EVENT SHALL EATON BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUEN-
TIAL DAMAGES (REGARDLESS OF THE FORM OF ACTION, WHETHER IN CONTRACT, STRICT
LIABILITY, OR IN TORT INCLUDING NEGLIGENCE), NOR FOR LOST PROFITS; NOR SHALL THE
LIABILITY OF EATON FOR ANY CLAIMS OR DAMAGE ARISING OUT OF OR CONNECTED WITH
THESE TERMS OR THE MANUFACTURE, SALE, DELIVERY, USE, MAINTENANCE, REPAIR OR
OPERATING YOUR FIXTURE
1.
Rotate knob on bottom of the sensor to
“TEST” (Fig. 7).
2.
Turn on the power to fixture. Allow fixture to warm
up approximately 40 seconds before testing. (Lights
may not come on during warm-up period.)
3.
Aim sensor head toward desired detection area,
maintaining a 5°–15° down angle to allow moisture
to drain.
4.
Walk across the detection zone at the farthest
distance you wish your detector to detect motion.
5.
Adjust sensor head angle until you get desired
results. Lights will turn off 4 seconds after all
motion stops.
NOTE:
For maximum range performance, allow fixture
to operate in any mode (with power to the unit) for at
least 48 hours.
6.
To set the ON time, rotate knob arrow to point to the
desired time setting within the TIME range (up to 12
minutes) (Fig. 8).
SELECTING YOUR DESIRED FEATURE
5
A
E
6
Junction
box
C
A
G
B
Quick Connect
wiring connector
+
-
TIME
TEST
7
+
-
TIME
TEST
8
Example of knob arrow
placement to set duration
of ON time.
Test Setting
Lights should turn ON with
motion both day and night.
Lights should turn OFF
after 4 seconds.
Turn the power
to the fixture ON.
TEST
Return to Auto Setting
(motion activated)
From any of the above settings
Knob arrow points to
desired time setting
within TIME range.
Turn the power OFF
for at least 40 seconds
and then back ON.
Mode of
MODE Knob
How to Set
Operation
Adjustment
Power Switch
Auto Setting (motion activated)
Lights should turn ON with
motion only at night and should
turn OFF according to the
TIME dial setting.
Knob arrow points to
desired time setting
within TIME range.
Turn the power
to the fixture ON.
Dusk to Dawn Setting
(activated only at night)
Lights should turn ON for 6 hours
at dusk and then reset to
the Auto Setting.
Knob arrow points to
desired time setting
within TIME range.
Turn the power
OFF and ON twice
within 3 seconds.
Problem
Cause / Solution
Light does not
come ON with
motion at night.
No power to the fixture.
• Check if circuit breaker tripped.
• Confirm wall switch is ON.
Surrounding external ambient light is too bright. (If so, the unit may
think it is daytime.)
• Re-aim the head.
• Relocate or reposition the unit away from the light.
TURN OFF POWER BEFORE CONTINUING
Wiring to the unit is loose.
• Check wiring; reconnect if necessary using wire nuts
(E) provided.
Light
comes ON
for no apparent
reason at night.
There is motion in the detection zone.
• Make sure the sensor is not picking up moving objects such as
trees, traffic, etc.
TEST FOR YOURSELF.
• Cover the sensor lens with cardboard to prevent sensor
from detecting motion. If the light stays off, something in the
detection zone is triggering the sensor.
* If the light stays on with the sensor lens covered, contact
customer service.
• Reposition the sensor.
Light stays ON at
night and does
not turn OFF.
There is motion in the detection zone.
• Make sure the sensor is not picking up moving objects such as
trees, traffic, etc.
• Reposition the sensor.
If there is no motion in the detection zone, unit is in “Dusk to Dawn
Setting” (override mode).
• Turn the light switch to the OFF position for 40 seconds, and
then turn back to the ON position. This will send the unit back
into the “Auto” mode.
Light
continuously
blinks ON and
OFF at night.
The light given from the unit’s own lamp is affecting the
motion sensor.
• Re-aim the lamp.
• Reposition motion sensor.
Light is ON
during the day.
The controls on the bottom of the motion sensor are in “TEST” mode.
• Change dial setting (not “TEST” mode).
The motion detector is shadowed.
• Reposition motion sensor.
Cannot activate
Dusk to Dawn
Setting at night
(override mode).
Surrounding external ambient light is too bright. (If so, the unit may
think it is daytime.)
• Re-aim the head.
• Relocate or reposition the unit away from the light.
Not enough time is allowed to enter the “Dusk to Dawn Setting.”
• Turn power OFF and ON twice within 3 seconds.
There is more than one fixture on an indoor wall switch.
• If so, put them on separate switches.
