background image

 

Laminate: This usually requires maximum 
tension for 100 micron films. 

Waste backing paper: This usually requires 
only slight tension but can vary from 
laminate to laminate Overtightening can 
cause the laminate to move which can cause 
creasing. 

  

  

  
  
  
  
  

  
  

  
  

8. 

 

    

Alter the speed to your preference  

  If you are using the Easymount   

by turning the speed control knob.        

Sign single hot, you can select Hot   

During loading we advise a slow          

or cold. Heat can help soften the   

Speed.   

  

  

  

     

Adhesive and reduce silvering.   

  

Switch the control panel to     

          Switch the control panel to foot   

Forward mode. [When not in use 

  

         pedal mode It is advisable to start   

w e advise you switch to off  to     

         . 

  During   

avoid accidental movement of    

         operation this can be pressed to    

the rollers]. 

  

  

  

         Auto mode and the machine will              

  

  

  

         run continually until the magic eye    

  

  

  

         is interrupted or the switch i s set   

  

  

  

         to Off mode.   

7. Apply tension to your laminate and waste backing 
paper by turning the handles clockwise. If the film 
looks creased or is not being drawn through the 
rollers smoothly, apply more tension.  

Switch the control panel to foot 
pedal mode. [During operation 
this can be pressed to auto 
mode and the machine will run 
continually until the magic eye is 
interrupted or the forward and 
reverse switch is set to off]. 

9. Press on the foot pedal to move the rollers forward, stop when the backing paper is towards the front of 
the roller as shown in the below picture. 

 

Summary of Contents for EM-S880

















Reviews: