background image

12

INSTALLATION GUIDE

13

INSTALLATION GUIDE

U S A

U S A

Easy Door Lock Sensor, LED Light Connector (CN5)

Easy Door Lock Sensor 

Doors can be locked (armed) or unlocked (disarmed) without the remote or car keys 
with this function.  Simply input the 4 digit pass-code by knocking on the Easy Door 
Lock Sensor on the front windshield.  

** On the pager model (E8-B), knocking twice on the sensor will send a call signal to 
the pager remote. However, it will not operate when the vehicle is on the ON position 
nor when the engine is running.

LED Light

 

The 10 digit blue LED displays various functions such as arming, disarming, valet 
mode and emergency status (panic, shock, and theft).    

➢ 

Dual Shock Sensor (CN6)

Install the sensor in a central loca-
tion and adjust its sensitivity after 
opening the door in accordance 
with different shocks and status of 
LEDs on the shock sensor. It sens-
es shocks by two steps (strong and 
weak shock).

Antenna Module (CN7)

Mount the antenna horizontally at the top left or right corner of the front windshield.  
The transmitting distance may decrease if the vehicle has a UV protective coating 
on the windshield.

Start Button (CN8)

1. Push button ON/OFF

<Ignition Off>

<Ignition On>

1-1) Engine ON

To start your vehicle, press the 
brake and press the Push-to-Start 
button.  The “STOP” will illuminate 
to red.
O n c e   t h e   p a r k i n g   b r a k e 
(automatic transmission) or the 
emergency brake (manual 
transmission)  is  released,  the     
red illumination will disappear.  Once the red "STOP" illumination disappears, 
you will not be able to stop the engine.

1-2) Engine OFF

To turn your engine off, press the brake and press the Push-to-Start button.  

Once the parking brake (automatic transmission) or the emergency brake 

(manual transmission) is engaged, the green illumination will appear on 

“START”.  

2. OFF 

 ACC 

 ON 

 OFF

<ON>

<ACC>

2-1) ACC

To enable the vehicle in the ACC mode, 

press the Push-to-Start button once 

without pressing on the brake

2-2) ON

To enable the vehicle in the Ignition ON 

mode, press the Push-to-Start button 

twice without pressing on the brake.

Summary of Contents for E8-B














Reviews: