8
heat tolerance, which may degrade at lower temperatures, are protected to prevent
degradation.
Minimum 24” (61 cm) must be provided at the centre of the appliance for burner
servicing.
When venting through a wall the vent terminal must be located at least 7.0 ft (2.1m)
above grade.
This appliance must be mounted at least 7 ft (2.1m) above the floor in Canada, and 8 ft
(2.4m) above the floor in the U.S.
Minimum clearances (inches and cm) from combustibles measured from radiant surface.
The clearances are reduced by 1/3, 15 ft (4.6 meters) from the burner of EZM models.
30
D
E
G
.
M
A
X
30
D
E
G
.
M
A
X
BELOW
ABOVE
ABOVE
ABOVE
ABOVE
BELOW
S
ID
E
S
ID
E
S
ID
E
S
ID
E
B
A
C
K
S
ID
E
S
ID
E
B
A
C
K
BELOW
BELOW
X
13
13
13
15
15
13
31
31
31
31
4
4
4
4
X
Minimum Clearance in inches to Combustibles/ Escape Libre Minimum En Pouce Entres Les
Materiaux Combustibles
HORIZONTAL/HORIZONTALE
30 DEG. ANGLE
Above/Sommet
Below/Dessous
Side/Cote
Back/Dos
30
D
E
G
.
M
A
X
30
D
E
G
.
M
A
X
BELOW
ABOVE
ABOVE
ABOVE
ABOVE
BELOW
S
ID
E
S
ID
E
S
ID
E
S
ID
E
B
A
C
K
S
ID
E
S
ID
E
B
A
C
K
BELOW
BELOW
X
33
33
33
38
38
33
79
79
79
79
10
10
10
10
X
Minimum Clearance in centimeters to Combustibles/ Escape Libre Minimum En cm Entres Les
Materiaux Combustibles
HORIZONTAL/HORIZONTALE
30 DEG. ANGLE
Above/Sommet
Below/Dessous
Side/Cote
Back/Dos
LABOUR REQUIREMENTS
Two persons are required to safely install this equipment. Wear gloves and other required
safety protection.
INSTALLATION IN COMMERCIAL AIRCRAFT HANGARS
Low intensity radiant tube heaters are suitable for use in aircraft hangars when installed
in accordance with the latest edition of the Standard for Aircraft hangars, ANSI/NFPA
No. 409 in the USA, or the Canadian Natural Gas and Propane Installation Code, B149.1
A minimum clearance of 10 ft (3m) above either the highest fuel storage compartment or
the highest engine enclosure of the highest aircraft, which may occupy the hangar. The
clearance to the bottom of the heater shall be measured from the upper surface of either
the fuel storage compartment or the engine enclosure; whichever is higher from the floor.
A minimum clearance of 8 ft (2.4m) must be maintained from the bottom of the heater to
the floor in other sections of the aircraft hangar, such as offices and shops, which
communicate with areas for servicing or storage. For proper mounting clearances, refer to
the clearances to combustibles in these installation instructions.
Heaters must be located where they are protected from damage to aircraft and other
objects, such as cranes and movable scaffolding.
Heaters must be located so as to be accessible for servicing and adjustment.
Summary of Contents for Middleman EZM-100-50
