background image

© Copyright 2016 Easthill Group, Inc.     8/16   Instruction item #21195Q     Rev 0

If you have any questions about the use of this product, please contact 

The Eastwood Technical Assistance Service Department: 800.544.5118  >>  email: [email protected]

PDF version of this manual is available online  >>  eastwood.com/21195manual

The Eastwood Company     263 Shoemaker Road, Pottstown, PA 19464, USA 

US and Canada: 800.345.1178     Outside US: 610.718.8335 

Fax: 610.323.6268     eastwood.com

ADDITIONAL ITEMS

#21196

 

Replacement Outer Lens

PROBLEM

CAUSE

CORRECTION

Auto-Dimming 

Does Not 

Function (Will 

not Darken)

Dirt may be blocking 

sensors located at 

upper area of the lens 

assembly

Clean Lens Assembly.

Batteries  

May Be Low

Expose the solar cells to bright light source 

to recharge.

Dirt may be blocking 

solar cells at lower 

portion of viewer area

Clean Lens Assembly.

Slow 

Response for 

Darkening

Operating 

Temperature Too Low

Do not use below 23°F (-5°C).

Poor Vision 

Through Lens

Dirt or Excessive 

Pitting May be 

Blocking View

Clean Lens Assembly.

Helmet Slips 

During Use

Helmet Fit Not 

Adjusted Properly

Follow fit adjustment steps in instructions.

Red LED Glows

Batteries require 

recharging or  

replacement.

Replace or Recharge Batteries per  

Battery Recharge/Replacement procedure 

in preceding Maintenance section.

TROUBLESHOOTING

Summary of Contents for 21195









Reviews: