background image

OUTDOOR USE ONLY / NEVER LEAVE UNATTENDED

    Page 7 of 18 

with Acme/Type 1/QCC1 Safety Valves).  These can be quickly identified because the valves have external 
threads. 

  LP gas is flammable, explosive under pressure, colorless, tasteless and heavier than air. It pools in low areas. 

  LP gas is naturally odorless, but a distinctive odor has been added by the LP gas supplier for your protection. 

  LP gas can cause skin to freeze on contact. 

  Burning LP gas consumes oxygen and produces carbon monoxide, a deadly gas. Never operate this appliance 

inside a building or confined area. 

  Carefully read and follow all instructions on LP tank. 

  The LP-gas supply tank must be constructed and marked in accordance with the specifications for LP-gas tanks 

of the U.S. Department of Transportation (DOT) CFR49 or the National Standard of Canada, 

CAN/CSA-B339, 

Cylinders, Spheres and Tubes for the Transportation of Dangerous Goods.

 

  Never use a LP tank with a damaged body, valve, collar or foot ring. A dented or rusty LP tank may be 

hazardous and should be checked out by a LP gas supplier. 

  Use only LP tanks that include a collar to protect the tank valve. 

  Do not store spare LP gas tanks under or near this appliance.  Never fill the tank beyond 80 percent full.  If 

these instructions are not followed exactly, a fire causing death or serious injury may occur. 

  When the appliance is not in use, the gas must be turned off at the supply cylinder.  Storage of the appliance 

indoors is permissible only if the cylinder is disconnected and removed from the appliance.  Always use and 
store LP tank in an upright position.  Never store or transport LP tank in occupied enclosures. LP tanks must be 
stored outdoors out of the reach of children and must not be stored in a building, garage or any other enclosed 
area. 

  Always perform a leak test on all gas connections whenever a tank is connected. If bubbles form in the leak test 

solution, do not use. Never use a flame to test for leaks. 

Step 1.5  Connecting the LP Gas Tank 

 
 
 

 

 
 
 
 

 

See figure 14 for the regulator control valve on 
left and high-pressure regulator on right.  See 
figure 15 for the QCC1 fitting. 

 

Fig. 14

 

Fig. 15

NOTE:

 The regulator control valve controls the flame intensity and acts as an On/Off valve when operating the 

appliance.  When finished cooking or in case of emergency, close the LP tank valve by turning LP tank valve 
clockwise until tight (Closed Position).  Be sure to close LP tank valve before disconnecting the hose. 

Make sure the regulator control valve is in the closed position by turning the valve clockwise until it is tight 
(figures 16 & 17).  This will not allow gas to flow through the hose.  

  

 

 

Fig. 16  

 

 

Fig. 17

Make sure the valve on LP tank is clean.  Attach regulator (in up position) and hose to LP tank by sliding the 
black portion of the QCC1 fitting overtop LP tank valve threads (figure 18).  Turn QCC1 fitting clockwise until 
hand tight (figure 19).  

Do not use a wrench to tighten Type I (QCC1) fitting (hand tighten only).

 

Clean and Inspect hose before each use. If evidence of abrasion, wear, 
cuts, or leaks, replace hose prior to operation. Replace only with Eastman 
Outdoors high pressure regulator assembly Model 90320.   

 

High pressure regulator and hose assembly supplied must be used.  Do 
not use high pressure regulator and hose assembly with any other gas 
appliance. 

 

Failure to follow these instructions can lead to fire or explosion, which 
could cause property damage, serious personal injury or death.

 

Summary of Contents for 37211



















Reviews: