16 Introduction
Machine Serial Number
An identification label is affixed to each
machine. The identification label displays
the Model Number, Serial Number, Year
of Manufacture, and Electrical Power
Requirements.
Record the Serial Number and Year of
Manufacture for future reference.
Note the electrical power characteristics
indicated below the Model and Year.
These specify the electrical power
requirements of the Case Erector.
Typical Applications
Eastey ERX-15 Automatic Case Erector
This case erector can be used for a wide range of applications where case size
minimum and minimum are within the minimum and maximum case size parameters
specified in the Box Specifications table of the ERX-15 Case Erector Specifications.
The case erector is particularly suited for moderate-sized boxes within the minimum and
maximum sizes specified. Boxes are erected from flat case blanks, bottom-folded and
tape-sealed, and delivered from the exit with the top open and ready to be filled and
sealed.
Do NOT use the Case Erector with the following products types
•
Explosive Products
•
Flammable Products
•
Hazardous Products
•
Pharmaceuticals
•
Agri-Foodstuffs
•
Products that are heavier or larger than allowed by the machine specifications.
Do not
operate the Case Erector in any extremely wet or oily environment that may
exceed operating specifications. Install the Case Erector in a closed, well-ventilated
area where there are no explosive or fire hazards. This equipment is designed for
indoor operation in a typical clean, dry factory environment protected from rain and
moisture. Do not spray water or wet-wipe the machine.
Make sure
the Case Erector is
level
and there is sufficient clearance around the to
allow personnel access for operation and maintenance of the Case Erector.
CASE ERECTOR
SEALING MACHINE
MODEL:
ERX-15
SERIAL:
YEAR:
Volt
230V
1 ~
1.56kW
50 Hz
6.8A
Phase
Watt
Ampere
Hertz
FILE ERX-15
450kg
6kA
Main document number
Weight
Short Circuit Rating
Summary of Contents for ERX Series
