background image

 

    Advanced RGB LED 1.0 Kit

 

 

 

December 2013, Rev 1

 

− 3 − 

http://www.EasternVoltageResearch.com 

Advanced RGB LED 1.0 Kit 

 

 

 
Circuit Description 
 

The Advanced RGB LED 1.0 utilizes a PIC12F683 microcontroller, U2, which outputs a 
3-channel pulse width modulated (PWM) signal which controls a single high power RGB 
LED  module,  D1.    The  output  PWM  signals  are  modulated  to  produce  a  wide  array  of 
colors, brightness levels, and effects that are used to control the current flowing through 
each of the red, green,  and blue dies of the  LED, D2, via the MOSFET transistors, Q1, 
Q2,  and  Q3.    Voltage  regulator,  U1,  provides  the  regulated  5VDC  required  by  the 
PIC12F683  microcontroller,  U2,  while  diode,  CR1,  provides  reverse  voltage  protection 
against a battery or power supply that is hooked up backwards.   
 
A  pushbutton,  PB1,  allows  the  user  to  cycle  through  the  various  modes  of  operation 
which include, but is not limited to, the following effects: 
 

 

Steady-state colors (red, blue, green, purple, white, yellow, cyan) 

 

Pulsing colors (red, blue, green, white) 

 

Different brightness levels for steady-state colors 

 

Strobe effects (red, white) 

 

Police strobes (red and blue alternating) – Different flashrates 

 

Mood light modes (cycles through all colors of the spectrum slowly) 

 
 
 
 
 
 

Summary of Contents for Advanced RGB LED 1.0














Reviews: