manualshive.com logo in svg

Eastern Voltage Research Advanced RGB LED 1.0, Instruction Manual

Introducing the Eastern Voltage Research Advanced RGB LED 1.0, a cutting-edge lighting solution revolutionizing your space. Illuminate with boundless colors and effects, controlled effortlessly. Unlock the full potential of this innovative product by downloading the free Instruction Manual from our website for a seamless user experience.

Share
Download
background image

 

    Advanced RGB LED 1.0 Kit

 

 

 

December 2013, Rev 1

 

− 10 − 

http://www.EasternVoltageResearch.com 

Advanced RGB LED 1.0 Kit 

 
Okay, so lets begin! 
 

 

1.  Install D1, High Power RGB LED Module.  The LED has polarity and should 
be  installed  so  that  the  anode  end  of  the  LED  is  pointing  towards  the  silkscreen 
DOT and notch on the board. The anode end of this particular LED is indicated by 
a notch in the corner of the LED as shown in the figure below. 

 

 

CAUTION: 

This device is heat sensitive.  Be sure to not apply too much heat while 

soldering or to leave the soldering iron in contact with the pad or part for 

more time than is necessary.  Excessive heat may damage this part. 

 
 

 

 

Place the LED on the board with the notch oriented toward the silkscreen DOT on 

the board. 

 

 

2.  Install R1, 220 ohm resistor (red-red-brown) 

 

 

3.  Install R2, 160 ohm resistor (brown-blue-brown) 

 

 

4.  Install R3, 160 ohm resistor (brown-blue-brown) 

 

 

5.  Install R4, 10 ohm resistor (brown-black-black) 

 

 

6.  Install R5, 10 ohm resistor (brown-black-black) 

 

 

7.  Install R6, 10 ohm resistor (brown-black-black) 

 

 

8.  Install CR1, 1N4148 diode.  The cathode band on the diode must match that 
shown on the silkscreen. 

 

Summary of Contents for Advanced RGB LED 1.0














Reviews:

No comments

Related manuals for Advanced RGB LED 1.0

Brands by name

Popular brands

Load more brands