EarthWise TC78510 Operator'S Manual Download Page 5

STAY ALERT - Watch what you are doing. Use 
common sense.  Do not operate the tiller/cultivator 
when you are tired or under the influence of drugs 
or medication. 
 

WARNING: 

Do not operate the tiller/cultivator 

near underground electrical cables, telephone 
lines, pipes or hoses. 
 
If the tiller/cultivator strikes a foreign body, turn it off 
immediately, wait for the tines to stop and check for 
damage. If necessary, repair before restarting. 
 
If the tiller/cultivator starts to vibrate abnormally, 
turn it off immediately and check for the cause.  
Vibration is generally a warning of trouble. 
 

DANGER: RISK OF CUT - 

Wear gloves and use 

caution when cleaning or performing maintenance 
on the tiller/cultivator.   
 
Always turn off the tiller/cultivator, disconnect from 
the power supply and wait until the tines come to a 
complete stop before carrying out any maintenance 
or repairs. 
 

CAUTION:

 Tines do not stop immediately after 

the tiller/cultivator is turned off. 
 

CAUTION: 

Risk of injury. Do not put hands, feet 

or any body part or clothing near the rotating tines. 
 

WARNING: California Proposition 65:   

 

This product contains chemicals known to the State 
of California to cause cancer, birth defects or other 
reproductive harm.

 

 
 

WARNING: 

Some dust and debris created by 

the use of this tool could contain chemicals known 
to the State of California to cause cancer and birth 
defects or other reproductive harm.  
Some examples of these chemicals are: 
   - chemicals in fertilizers 
   - compounds in insecticides, herbicides, and  
     pesticides 
   - arsenic and chromium from chemically treated    
      lumber 
Your risk from exposure to these chemicals varies, 
depending on how often you do this type of work. 
To reduce your exposure, work in a well-ventilated 
area and with approved safety equipment such as 
dust masks that are specially designed to filter out 
microscopic particles. 

GROUND FAULT CIRCUIT INTERRUPTER (GFCI) 
protection should be provided on the circuit or outlet 
to be used for the tiller/cultivator. Receptacles are 
available having built-in GFCI  protection and may 
be used. 
 
DISCONNECT UNIT from the power supply when 
not in use or when servicing or cleaning.  Do not 
leave unattended. 
 
DON’T ABUSE CORD - Never carry this product   
by the cord or yank the cord to disconnect from the 
receptacle.  Keep cord from heat, oil, and sharp 
edges. 
 
USE RIGHT APPLIANCE - Do not use this product 
for any job except that for which it is intended. 
 
DON’T OVERREACH - Guide the tiller/cultivator at a 
walking pace only. Keep proper footing and balance 
at all times.  
 
LIGHTING - Only operate your tiller/cultivator in  
daylight or good artificial light. 
 
STORE IDLE UNIT INDOORS-When not in use, the 
tiller/cultivator should be stored indoors in a dry area 
out of children’s reach. 
 
MAINTAIN UNIT WITH CARE-Keep clean for best 
performance and to reduce the risk of injury. Inspect 
extension cord periodically and replace if damaged.  
Keep handles dry, clean and free from oil. 
 
POLARIZED PLUGS-To reduce the risk of electric 
shock, this product has a polarized plug. Polarized 
connections will fit together only one way. Make 
sure that the receptacle end of the extension cord 
has large and small blade slot widths. If the plug 
does not fit fully into the extension cord, reverse the 
plug. If it still does not fit, obtain a suitable extension 
cord.  If the extension cord does not fit fully into the 
outlet, contact a qualified electrician to install the 
proper outlet. Do not change the plug on the tool or 
the extension cord in any way. 
 
Do not operate the tiller/cultivator on a slope that is 
too steep for safe operation. When on slopes, slow 
down and make sure you have good footing. 
 
Before starting the tiller/cultivator make sure the 
times are not touching any object and are free to 
move. 
 
Grip the guide bar firmly with both hands. Never  
operate the tiller/cultivator with one hand. 
 

CAUTION: 

The tiller/cultivator may bounce up-

ward and/or jump forward if the tines strike extreme-
ly hard packed soil, frozen ground, or buried obsta-
cles such as large stones, roots or stumps. 

GENERAL SAFETY

 

Summary of Contents for TC78510





































Reviews: