background image

PAGE 3

1/4 - 20 Locknut

1/4 - 20 x 1-1/2” Bolt

1/4 - 20 x 1-1/2” Bolt

1/4 - 20

Locknut

Gauge & Linkage Assembly

Control Lever

& Gauge

12. 

CALIBRATION: 

This step ensures that your spreader is 

properly adjusted to give you a correct starting point to apply 

materials at the correct setting.

 

 

Pull the Control Lever back to #30 on 

the Gauge, then push the shut-off plate forward until the shut-off and the drop holes 

are fully open.  Now tighten the Hex Nut on the  ½” Carriage Bolt on the Linkage 

Assembly.  Check to confirm calibration by closing the Control Lever, then reopening 

to #30 and confirm that the drop holes are fully open.

13. 

Insert agitator to pinion shaft on inside of hopper.  

NOTE:

 Position of flat side of the agitator as shown at the 

right.

10.

 Attach Linkage Pivot with 1/4-20 x 1½” Hex Bolt, 

Flat Washer, Spacer and Locknut as shown below.  

Next

, install Control Rod into the Shut-Off Plate as 

shown at the right.  

TIP:

 Make sure that the Control 

Rod is above the Lower Handles.

60088 

Gauge & Linkage

12147 

Spacer

32103

1/4-20 Locknut

31100

1/4-20 X 1-1/2" Bolt

and 34108 Washer

41256

Control 

Rod

36500

1/2” Carriage 

Bolt

34100

Washer

32108

Hex Nut

60088

Linkage

12317

Shut-off

Plate

41256

Control

Rod

25304

Handle Shaft

12317

Shut-Off

Plate

60088

Linkage

32108

Hex Nut

34100

Washer

41256

Control 

Rod

11.

 Using ½” Carriage Bolt, install through the Control Rod, Linkage and install the 

Flat Washer and secure with Hex Nut to a loose fit to allow for 

CALIBRATION 

below.  See above right and below for details.

Summary of Contents for 2600A-Plus Estate








Reviews: