background image

2

XJ-300ST Manual

Earthquake Sound Corp. | www.earthquakesound.com

XJ-300ST Manual

3

Specifications are subject to change without notice

Earthquake Sound Corporation
2727 McCone Avenue
Hayward, CA 94545
Tel: 510-732-1000
Fax: 510-732-1095

Customer Support
[email protected]
Tel: 800-576-7944
Fax: 510-732-1095

© 2019 Earthquake Sound Corporation. All rights reserved.

This document should not be construed as a commitment on the part of Earthquake
Sound Corporation. The information is subject to change without notice. Earthquake
Sound Corporation assumes no responsibility for errors that may appear within this
document.

Safety Instructions

Safety First

This documentation contains general safety, installation, and operating
instructions for XJ-300ST. It is important to read this user’s manual before
attempting to use these products. Pay particular attention to the safety
instructions.

Symbols Explained:

Note:

Appears on the component to indicate the presence of
uninsulated, dangerous voltage inside the enclosure – voltage
that may be sufficient to constitute a risk of shock.

Calls attention to a procedure, practice, condition or the like
that, if not correctly performed or adhered to, could result in
injury or death.

Calls attention to a procedure, practice, condition or the like
that, if not correctly performed or adhered to, could result in
damage to or destruction of part or all of the product.

Calls attention to information that is essential to highlight.

Safety Instruction

2) Store this manual and packaging in a safe place.

1) Read these instructions in their entirety.

3) Heed all warnings.

4) Follow instructions (do not take short cuts).

5) Do not use this apparatus near water.

6) Clean only with a dry cloth.

7) Do not block any ventilation openings. Install in accordance with the

manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves,

or other apparatuses that produce heat.

9)

Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plus has two blades with one wider than the other. A grounding-
type plug has two blades and a third grounding prong. The wide blade or the
third prong is provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched, particularly at

plugs, convenience receptacles, and the pint where they exit from the
apparatus.

11) Only use attachments & accessories specified by the manufacturer.

12) Use only compatible rack or cart for final resting position.

13) Unplug this apparatus during lightening storm or when unused for a long

period of time.

14) Refer all servicing to qualified service personnel. Servicing is required

when the apparatus has been damaged in anyway, such as: power- supply
cord or plug is damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.

15) To reduce the risk of fire or electric shock, do not expose this apparatus to

rain or moisture.

The Sound That Will Move You

Summary of Contents for XJ-300ST











Reviews: