background image

   

   

23   

If this switch is noted to be in the actuated position upon 
power-up, the controller will not start furnace operation and 
an LED error flash cadence is set to indicate the problem. 

Further, during a reset operation the electromechanical 
reset switch must not only be actuated for one second or 
longer but the switch must be released before the IBC 
assembly will reset. 

The  temperature  sensor  inputs  are  hardware  biased 
towards over-range or under-range conditions as 
appropriate. In the event of a disconnected sensor, the 
firmware can detect that the sensor is missing or shorted by 
testing for sensor under-range and over-range conditions, as 
is appropriate for a given sensor. 

The IBC assembly will detect that the water temperature 
sensor is missing and will shut down the furnace, and an LED 
error flash cadence will be set to indicate the problem. 

The potentiometers on the IBC assembly that are used to set 
the water temperature high limit and water temperature low 
limit are monitored for reversed settings. If the water 
temperature high limit is set to a lower temperature than the 
water temperature low limit temperature setting, the IBC 
assembly will detect this reversed setting condition and the 
furnace will be shut down resulting in a LED error flash 
cadence to indicate the problem. 

LED Indicator Error Cadences 

In order to communicate diagnostic information to the 
user of the Earth Outdoor Furnace, the LED indicators that 
are visible on the front panel of the IBC controller assembly 
will flash as required in order to indicate various 
operational alerts and alarms. The error cadences and their 
meanings are as follows: 

Water Jacket Temperature below 150°F 

Call for heat amber LED will pulse 

Summary of Contents for Klear Sky 400


























































Reviews: