background image

7

TURBINE UNIT

The turbine unit only requires minimal maintenance

Ensure its filter element is kept clean at all times.
This is the filter underneath the main body of the Motor Unit (28). Disconnect the unit from the mains, 
turn on side and remove foam material. This can be washed out if necessary and replaced when dry. From

time to time this filter will need replacing (part no.L0058).

The turbine bearings are sealed and lubricated for life. There is no maintenance or adjustment required.

Clean the turbine and hose unit with a damp cloth after use.

The hose is stored by coiling it between the motor housing and hose cover.

The mains lead is stored by wrapping around the base of the unit and locating the plug in the space at the
back of the unit.

TROUBLE SHOOTING

PROBLEM CAUSE 

ACTION 

REQUIRED

The paint runs on the 

Paint too diluted 

Add undiluted material

item being sprayed 

Paint volume too high 

Reduce the paint flow by adjusting screw (12)

 

Moving too slowly 

Increase speed of application

 

Gun trigger being held for 

Release trigger earlier

 too 

long

 

Gun too close 

Increase the distance between gun and 

  

workpiece

Paint is thin or 

Paint too diluted 

Add undiluted material

irregular 

Paint volume too low 

Increase the paint flow by adjusting screw (12)

 

Moving too fast 

Reduce speed of application

 

Gun clogged 

Clean the gun

 

Gun too far away 

Reduce the distance between gun and workpiece

No paint being 

Paint too thick 

Add thinner

produced 

Gun clogged 

Clean the gun

 

Pick up tube clogged 

Clean pick up tube (24)

 

Air hose split 

Replace air hose

 

Grainy paint 

Filter the paint

 

Container almost empty 

Refill container

 

Gun at an angle 

Ensure Pick up tube is angled towards paint

 

Air intake blocked 

Check no paper or loose debris can block the

 

 

air intake underneath the unit

MAINS CONNECTION

This unit is a Class II appliance which means it is double insulated for your protection, no earthing wire is
necessary.
If the supply cord is damaged, it must be replaced by Earlex Ltd or our appointed agents.
Your unit has been supplied with a mains lead with a fitted plug. This is identified by the fuse holder in the base
of the plug. Please read the following safety instructions before use.

1

. If the fitted plug is cut off from the mains lead then the plug must be disposed of safely. 

NEVER

under any

circumstances insert such a plug into a 13 amp socket.

2. NEVER

under any circumstances use the appliance or mains lead without the fuse cover fitted.

This is the little cover fixed into the base of the plug to hold the fuse in place.

3. 

If you lose the fuse cover then please contact any electrical dealer for a replacement or ring our helpline.

4

. A replacement fuse must be rated at 5 amp. These must be manufactured and approved to BS 1362.

5. IF IN ANY DOUBT CONTACT AN ELECTRICIAN.

If you need to fit a plug to the mains lead, this should be fitted in accordance with the wiring instructions below,
and will need to be used with a 5 amp fuse. If in doubt consult an electrician.
If you are using an extension lead it must be rated at a minimum of 6 amps and fully unwound. Do not operate
with a lead rated at less than 6 amps as this will cause premature failure of the motor which is not covered by
the guarantee.
As the colours of the wires in the mains lead of the application may not correspond with
the coloured markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured blue must be connected to the terminal which is marked
with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal which is marked
with the letter L or coloured red.

L0199 09-04.qxd  14/2/05  10:13 am  Page 7

Summary of Contents for SPRAY STATION PRO HV 5000









Reviews: