background image

●  

CAUTION: TO REDUCE THE RISK OF  

ELECTRIC SHOCK OR INJURY, DO 
NOT USE IN THE RAIN. STORE 
INDOORS

The substances used with this spray 

applicator (paint, thinners etc) may contain 
hazardous, harmful, explosive or corrosive 
materials. 

ALWAYS COMPLY WITH THE SAFETY 

INSTRUCTIONS ISSUED WITH THIS 
PRODUCT AND THE MATERIAL BEING 
USED.

The spray applicator must only be used with 

paints and solvents that have a suitable flash 

point for spraying. If in doubt, consult the paint 

or solvent manufacturer's data

Always ensure there is adequate ventilation 

when spraying.

NEVER spray near an open flame, including 

an appliance pilot flame.

NEVER smoke when spraying.  

Always disconnect the unit from the mains 

supply when re-filling the paint container.

Always disconnect the unit from the mains 

supply when cleaning the spray applicator.

Always ensure the spray area is safe and free  

from all debris that may present a fire or trip 
hazard.

NEVER, under any circumstances, point the 

spray gun at another person or animal. In the 

event of injury occurring, seek expert medical 

advice immediately.

NEVER allow children or unauthorised users 

to operate or play with the spray equipment. 
This equipment is for professional use only.

Always read the paint manufacturer's thinning  

instructions before use.

Always wear the correct protective face mask  

when spraying. We also recommend wearing  

gloves, goggles and overalls.

After every use ensure that you clean the 

spray applicator thoroughly & grease the 
gland washer.

Use only genuine manufacturer replacement 

parts.

Only use the spray equipment as detailed in 

these instructions.

Do not use the air hose or mains cable to pull 

the turbine unit.

Check the hoses, hose connectors & mains 

cable daily. Any worn or damaged parts 
should be replaced immediately.

●   

We recommend the use of ear protectors.

●   

This appliance is not intended for use by 

persons (including children) with reduced 
physical, sensory or mental capabilities, or  
lack of experience and knowledge, unless 
they have been given supervision or 
instruction concerning use of the appliance 
by a person responsible for their safety.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  

   

 

 

   

 

 

SAFETY OPERATING INSTRUCTIONS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  

   

 

 

   

 

 

 

 

PLEASE READ BEFORE USE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

Summary of Contents for SPRAY PORT HV 7000













Reviews: