background image

The material contained in this document is the property of Electronics & Innovation Ltd., it is subject to 
change without notice.  
 

July 2012                                                                                                                      Revision I 

 

 

Warranty 

 
Electronics & Innovation Ltd., (hereafter E&I) warrants for the period of three years from 
the date of original delivery, each unit to be free of defects in materials and workmanship. 
For the period of 36 months E&I will, at its option, repair or replace defective parts so as 
to  render  the  unit  fully  operational  such  that  it  performs  according  to  the  original 
specifications; free of charge to the original purchaser.  
 
Should warranty service be required, the unit must be returned to E&I, freight cost to be 
borne  by  the  owner.  If,  in  our  opinion,  the  unit  has  been  damaged  by  use  outside  the 
limits prescribed in this manual or by accident, then the warranty shall not be honored. In 
such  a  case  E&I  will  provide  an  estimate  for  repair,  assuming  repair  is  possible  and 
provide a quote at standard service rates. 
 
 
 
 
 

Contents 

 
Chapter 1 
 

General Information……………………………………………………………3 

 

 

 

Chapter 2 
 

Operation………………………………………………………………………..4 

 
Chapter 3 
 

Technical Information

………………………………………………………….7 

 
Chapter 4 
 

Mainte

nance……………………………………………………………………8 

 
Chapter 5 
 

Safety……………………………………………………………………………12 

 
 
 

 

Summary of Contents for 2100L













Reviews: